1996 Oldsmobile Silhouette
Safety Recalls & Notices
We found 4 safety recalls for the 1996 Oldsmobile Silhouette. Recalls are sourced from both NHTSA (US) and Transport Canada databases. Contact your authorized Oldsmobile dealer to schedule free repairs.
Summary
On certain vehicles, the lower pinion bearings retainer tabs were not crimped properly. These and some other retainers used in vehicles assembled between January 1, 1996 and October 31, 1997 may fail and permit the ball bearings to escape. If the problem were to occur, the driver would have to exert more effort to turn the steering wheel. Correction: Dealers are to inspect the condition of the lower bearing, and replace the lower pinion bearing or the rack and pinion steering gear assembly, if necessary.
Summary
On certain vehicles operated in areas of high salt use, the spare tire hoist cable may corrode and eventually break. This would allow the spare tire to fall off the vehicle possibly resulting in a road hazard for other vehicles. Correction: A letter will be sent to owners of affected vehicles with maintenance and inspection instructions for spare tire hoist cable assemblies. Additionally, the letter will advise the owner that, if the cable breaks during that inspection, their dealer will repair the assembly. This policy will be in effect until December 31, 2002.
Summary
CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.
Potential Consequence
FUEL MAY LEAK, POSSIBLY RESULTING IN A FIRE.
Remedy
DELPHI WILL NOTIFY OWNERS AND REPLACE THE UPR FREE OF CHARGE. THE RECALL BEGAN ON APRIL 23, 2007. OWNERS CAN CONTACT DELPHI AT 877-411-8770.
Summary
CERTAIN PASSENGER VEHICLES AND MINI VANS HAVE LOWER PINION BEARINGS IN THE POWER RACK AND PINION ASSEMBLY IN WHICH THE RETAINER TABS WERE NOT CRIMPED PROPERLY. THESE AND SOME OTHER RETAINERS USED IN VEHICLES ASSEMBLED BETWEEN JANUARY 1, 1996 AND OCTOBER 31, 1997, COULD FAIL AND PERMIT THE BALL BEARINGS TO ESCAPE.
Potential Consequence
IF THIS OCCURS, THE PINION SHAFT CAN BE FORCED UPWARD DURING LEFT TURNS AND BACK DOWN AS THE STEERING WHEEL IS MOVED BACK AND TO THE RIGHT. IF THE PINION SHAFT MOVES FURTHER, THE DRIVER WILL NEED TO EXERT MORE EFFORT TO TURN THE STEERING WHEEL, SIMILAR TO A VEHICLE WITHOUT POWER ASSISTED STEERING. IF THE PINION SHAFT MOVES EVEN FURTHER, THE DRIVER WILL REQUIRE MUCH HIGHER EFFORT TO TURN LEFT AND MAY NOT BE ABLE TO TURN THE WHEEL AS MUCH AS INTENDED. WITH THE MAXIMUM PINION SHAFT MOVEMENT, WHICH REQUIRES INTERNAL GEAR COMPONENT DAMAGE, THE DRIVER CAN ENCOUNTER HIGH RESISTANCE TO TURNING LEFT, FOLLOWED BY UNINTENDED POWER ASSIST TO THE RIGHT. IN ANY OF THESE CONDITIONS, A CRASH COULD OCCUR.
Remedy
DEALERS WILL INSTALL A NEW LOWER PINION BEARING UNLESS INSPECT OF THE EXISTING BEARING INDICATES THAT REPLACEMENT OF THE GEAR ASSEMBLY IS NECESSARY. OWNER NOTIFICATION BEGAN JANUARY 24, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020, PONTIAC AT 1-800-762-2737, OR OLDSMOBILE AT 1-800-442-6537.
4 Active Recalls
Requires attention
1996 Oldsmobile Silhouette Recall FAQs
Common questions about recalls for this vehicle
Related Recall Checks
Compare recall history with competitors and alternatives to the 1996 Oldsmobile Silhouette.