Oldsmobile · 1990–2004
Silhouette Recalls
17 known recalls affecting the Oldsmobile Silhouette (1990–2004). Enter your VIN to check if your specific vehicle is affected, or browse by model year below.
Oldsmobile Silhouette Recalls
Summary
On certain Aztek (AWD), Montana (AWD), Relay (AWD), RendezVous (AWD), RendezVous (FWD), Silhouette (AWD), Terraza (AWD), Terraza (FWD), Uplander (AWD) and Venture (AWD) vehicles equipped with independent rear suspension, when operated in extreme cold temperature and on rough roads, water and salt can intrude past the ball joint seal. The combination of theses conditions may then lead to premature wear of the ball joint. If the ball joint wear progresses to the point of separation from the lower control arm, a loss of vehicle control may occur. Correction: Dealers will replace both ball joints with new ball joints which have a revised boot and ball stud to improve the seal to the ball stud shaft.
Summary
On certain vehicles equipped with second-row bucket seats or captain's chairs and power sliding door on the passenger side, if a passenger uses the interior handle to open the power sliding door and holds onto the handle while it is being opened by the motor, the passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury may result. Correction: Dealers will replace the original interior power sliding door handle. The original handles are offset from the door panel and a passenger can wrap his or her fingers around them. The replacement door handles are essentially flush with the door trim, preventing a passenger from gripping them in the same fashion.
Summary
On certain vehicles, the aluminum wheels are not marked with "T" and "DOT" as required by CMVSS 120. Correction: Since this does not pose any safety risk, no corrective action is required.
Summary
Certain vehicles do not comply with CMVSS 225 and 210.2. The Owner's Manual does not include the location symbols for the Lower Universal Anchorage System for Restraint Systems and Booster Cushions and an explanation of the meaning of the symbols. Correction: Owner's will receive an Owner's Manual supplement.
Summary
On certain vehicles, the passenger air bag was manufactured without a check pin. An air bag without the check pin could produce increased pressure at the onset of the air bag deployment and reduced pressure afterward. This could increase the severity of injury to a person who was not properly restrained and who was close to the passenger air bag at the time of deployment. It could also reduce the ability of the air bag to protect a restrained front seat passenger. Correction: Dealers are to inspect, and if necessary, replace the passenger air bag.
Summary
On certain vehicles, the lower pinion bearings retainer tabs were not crimped properly. These and some other retainers used in vehicles assembled between January 1, 1996 and October 31, 1997 may fail and permit the ball bearings to escape. If the problem were to occur, the driver would have to exert more effort to turn the steering wheel. Correction: Dealers are to inspect the condition of the lower bearing, and replace the lower pinion bearing or the rack and pinion steering gear assembly, if necessary.
Summary
Certain vehicles may have a driver's side airbag inflator that could fracture at a weld during a deployment. Pieces of the inflator could strike and injure vehicle occupants and the airbag cushion would not inflate fully, reducing the capacity of the bag to protect the driver. Correction: Dealers are to inspect and if necessary replace the driver side airbag module assembly.
Summary
Certain vehicles have an improperly programmed vehicle theft deterrent system. Correction: dealers will reprogram the system.
Summary
Certain 1997-2001 Chevrolet Venture, Pontiac Montana/ Trans Sport, and Oldsmobile Silhouette mini vans equipped with passenger side power sliding doors that were serviced in campaign 01013 (01v-067) from April to August 2001. Also 2001 Chevrolet Venture, Pontiac Montana, and Oldsmobile Silhouette mini vans equipped with passenger side power sliding doors assembled in January through April 2001. These vehicles have inadequate front welds. If a front weld fails, the actuator can jam in the unlatched position and, when the sliding door closes, it will not be latched. If this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface. An unrestrained occupant could fall out of the van and be injured. Correction: dealers will inspect the actuators for certain date codes and, if necessary, replace the actuators.
Summary
Certain vehicles may exhibit a condition in which the power sliding door closes, but is not latched, If this happens the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface. An unrestrained occupant could fall out of the vehicle and be injured. Correction: Dealers will install a new power sliding door un-latch actuator assembly.
Showing 1-10 of 17 recalls
Related Recall Checks
Check recalls for specific Oldsmobile Silhouette model years