Toyota · 2009–2024
Venza Recalls
11 known recalls affecting the Toyota Venza (2009–2024). Enter your VIN to check if your specific vehicle is affected, or browse by model year below.
Toyota Venza Recalls
Summary
Issue: Under certain conditions, a software problem could cause the rearview camera image to freeze or not to display. If this happens, the rearview image may not display when the transmission is shifted into reverse. Canadian regulations require the rearview image to display when the vehicle is reversing. Note: This recall only affects certain vehicles equipped with a panoramic view monitor system. Safety Risk: A rearview camera image that doesn't display correctly could reduce a driver's ability to see behind the vehicle while backing up. This could increase the risk of a crash. Corrective Actions: The company will notify owners in writing and advise you to take your vehicle to a dealership to update the parking assist ECU software.
Summary
Issue: On certain vehicles, a software problem could cause the combination meter in the instrument panel not to display when the vehicle is started. As a result, you may not be able to see certain information about the vehicle, including the speedometer, fuel gauge, warning lights and malfunction tell-tales. Note: This recall only affects vehicles equipped with a 12.3-inch display. Safety Risk: Warnings, tell-tales and gauges that don't display could increase the risk of a crash. Corrective Actions: The company will notify owners by mail and advise you to take your vehicle to a dealership to update the combination meter software. For certain vehicles, the dealer will also inspect and, if necessary, replace the combination meter.
Summary
Issue: Under certain conditions, the vehicle stability control (VSC) system may not switch on when the ignition is restarted. This can happen if the driver manually turns off the VSC, depresses the brake pedal, and then turns off and restarts the vehicle while continuously depressing the brake pedal. Canadian regulations require the stability control system to be active each time that you start the vehicle. Safety Risk: A stability control system that is switched off could increase the risk of a crash. Corrective Actions: The company will notify owners by mail and instruct you to take your vehicle to a dealer to update the skid control ECU software.
Summary
Issue: On certain vehicles, the rear turn signal bulbs could short circuit. If this happens, the turn signals and hazard lights may dim or may not work properly. Note: This problem can cause the turn signal indicator on the instrument panel to flash quickly. Safety Risk: Turn signals that do not work properly could cause a following driver not to recognize that a vehicle ahead intends to turn. Hazard lights that do not work properly could make the vehicle less visible. This could increase the risk of a crash. Corrective Actions: Toyota will notify owners by mail and instruct you to bring your vehicle to a dealer to replace both rear turn signal bulbs. The dealer will also replace the rear turn signal lamp assemblies, if necessary.
Summary
Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.
Summary
Issue: On certain vehicles, the wiring for the airbag sensor in the driver's door could be damaged over time. If this happens, the side airbag and curtain airbag on the driver's side may not work properly in a crash. Note: This problem may cause the SRS warning lamp to turn on in the instrument cluster. Safety Risk: Airbags that do not work properly could create an increased risk of injury in a crash. Corrective Actions: Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to inspect the driver's door wire harness. It will be replaced, if necessary.
Summary
On certain vehicles, the electrical power cords of some dealer installed block heaters may have been improperly manufactured, causing the wires to contact each other, resulting in a short circuit. A short circuit could lead to a fire which would increase the risk of injury and/or damage to property. Correction: For vehicles where the subject block heater was approved for installation, the dealer will replace the block heater assembly with a new one of an improved design. For vehicles where the subject block heater was not approved for installation, dealers will remove the block heater assembly. In the interim, until the remedy can be performed, dealers will cut the plug end from the block heater cord to disable the block heater's operation.
Summary
On certain vehicles, if the air conditioning condenser drain hose were to become clogged, water could accumulate and leak onto the airbag control module. This could cause the airbag warning light to illuminate, and potentially result in an unintended deployment of the airbags. This could startle the driver and/or cause minor injuries to vehicle occupants. Water damage could also cause a loss of power steering assist, causing the vehicle to revert to a manual steering mode which would require greater driver effort, especially at low vehicle speeds, and increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will install a protective shield and sealant.
Summary
On certain vehicles, silicone grease may have come into contact with the stop lamp switch during vehicle assembly. If grease infiltrates the switch, instrument panel warning lamps could illuminate, a no start condition could result, or the shift lever may not shift from the PARK position. In some instances, the vehicle stop lamps could become inoperative. Failure of the stop lamps to illuminate when the brakes are applied may result in the following road users being unaware of the driver's intentions, increasing the risk of a crash causing property damage and/or personal injury. Correction: Dealers will replace the stop lamp switch.
Summary
On certain AWD vehicles, the right front driveshaft may not have received adequate heat treatment during the manufacturing process. As a result, the driveshaft could break. Failure of the right front driveshaft would result in a complete loss of vehicle propulsion which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the right front driveshaft.
Showing 1-10 of 11 recalls
Related Recall Checks
Check recalls for specific Toyota Venza model years