2002 Ford Escape
Safety Recalls & Notices
We found 19 safety recalls for the 2002 Ford Escape. Recalls are sourced from both NHTSA (US) and Transport Canada databases. Contact your authorized Ford dealer to schedule free repairs.
Summary
A safety defect may exist in vehicles in which remanufactured automatic transmissions were installed as service replacement parts. The shift lever bolt may not have been torqued to the proper torque specification. If the improperly torqued shift level bolt loosens and backs out, the shift lever may disengage from the transmission without warning, and the transmission may not respond to the shifter selection movement by the operator. This could result in the loss of transmission gear selection, and possible unintended vehicle movement, which would increase the risk of a crash causing injury and/or property damage. Correction: Dealers will inspect, and if necessary, replace the shift lever assembly and/or the shift level bolt torqued to the proper specification.
Summary
On certain vehicles registered and operated in areas where road salt is used on the roadways during winter months for extended time periods (Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island and Newfoundland-Labrador), the forward attachment point for the lower control arm may separate from the vehicle's subframe. This could affect vehicle handling and increase the risk of a crash causing injury and/or property damage. Correction: Dealers will install a newly designed reinforcement cross-brace.
Summary
On certain vehicles equipped with a 3.0L V6 engine and speed control, inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. A stuck throttle may result in very high vehicle speeds and make it difficult to slow or stop the vehicle if the transmission is not shifted into neutral. This could result in a crash causing property damage and/or personal injury. Correction: Dealers will replace the rear engine cover fastener, which will raise the cover in the area of the speed control cable to provide adequate clearance between the cover the speed control cable connector.
Summary
Certain vehicles may have been originally equipped with a brake master cylinder reservoir cap that could leak. If brake fluid leaks from the cap, it could come in contact with the ABS module wiring harness connector. The same vehicles were previously involved in campaign 2007107 to address potentially missing or misplaced seals in the wiring harness connector to the ABS module electronic control unit. If this repair wasn’t done correctly, brake fluid leaking from the reservoir cap could corrode the ABS module electrical connector. This could result in vehicle fire causing property damage and/or personal injury. Correction: Dealers will replace the brake master cylinder reservoir cap and modify the ABS electrical system. Note: Owners are advised to park the vehicle outdoors until the remedy is applied.
Summary
On certain vehicles, the electrical wiring connector to the ABS module may have been manufactured incorrectly. Over time, contaminants can enter the ABS electrical connector interface and corrode the terminals. This could cause the ABS warning indicator to illuminate, an open fuse, and in some instances, smoking, melting or burning of the electrical connector, with the potential for a fire while the vehicle is unattended. In addition, ABS function may be lost. Correction: Dealers will inspect and, if required, repair the wiring connector.
Summary
On certain vehicles equipped with 3.0L V6 engines, the accelerator cable's inner liner may, over time, migrate out of the conduit at the dash panel fitting during vehicle operation. The liner may migrate to the point that it contacts the accelerator pedal arm. Under these conditions the liner may prevent the pedal from fully returning, which may not allow the throttle body to fully return to the "idle" position. Typically the condition results in a progressive increase in the "idle" speed if liner migration continues over time, but may cause a more sudden increase if a greater portion of the cable moves at one time. An unexpected increase in "idle" speed may result in longer than expected stopping distances, which could potentially lead to a crash. Correction: Dealers will replace the accelerator cable.
Summary
On certain vehicles equipped with a 3.0L V6 engine, during deceleration at vehicle speeds below 64 km/h, the engine may stall due to an excessively rich fuel-air mixture. Correction: Dealer will reprogram the Powertrain Control Module.
Summary
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Potential Consequence
If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy
Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Summary
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Potential Consequence
If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy
Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Summary
The Timken Company (Timken) is recalling certain aftermarket front wheel bearings, part number 510072, sold from January 22, 2015, to May 21, 2015, to be used as service parts on 2001-2012 Ford Escape, 2001-2011 Mazda Tribute, and 2005-2011 Mercury Mariner vehicles. The affected wheel bearings have incorrect dimensions of a 42mm bore, 76mm outer dimension, and 39mm width, instead of a 42mm bore, 78mm outer dimension and a 45mm width.
Potential Consequence
Use of an incorrectly sized wheel bearing can adversely affect the braking and steering of the vehicle, increasing the risk of a crash.
Remedy
Timken has begun notifying distributors who will offer purchasers replacement wheel bearings, free of charge. The recall began on May 21, 2015. Owners may contact Timken customer service at 1-866-984-6536.
19 Active Recalls
Requires attention
2002 Ford Escape Recall FAQs
Common questions about recalls for this vehicle
Related Recall Checks
Compare recall history with competitors and alternatives to the 2002 Ford Escape.