2003 Chevrolet Express

Safety Recalls & Notices

Total
24
safety notices
Units
3,143
vehicles affected
Recent
Apr 6, 2023
last notice date

24 Active Recalls

Requires attention

Electrical

Apr 6, 2023Transport CanadaCampaign: 2023210

Summary

Issue: On certain vehicles, an unused wiring harness for a rear HVAC blower motor, located in the left B-pillar area, could become damaged if exposed to moisture or contaminants. If this happens, the wires could short circuit. Note: This recall only affects cutaway chassis incomplete vehicles. Safety Risk: A short circuit can create the risk of a fire. Corrective Actions: General Motors will notify owners by mail and instruct you to bring your vehicle to a dealership to seal the wiring for the rear HVAC blower motor at the left B-pillar.

Units Affected:25
Contact authorized dealer for service

Fuel System

Aug 8, 2012Transport CanadaCampaign: 2012265

Summary

On certain vehicles equipped with a left side cargo door, and originally sold in or currently operated in areas of heavy road salt usage during winter months (Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island, and Newfoundland & Labrador), the fuel filler pipe could corrode and become perforated. This could allow fuel to leak onto the ground while refuelling the vehicle. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will replace the fuel filler pipe.

Units Affected:951
Contact authorized dealer for service

FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP

Invalid DateNHTSACampaign: 92540

Summary

General Motors (GM) is recalling certain model year 2003-2004 Chevrolet Express and GMC Savana vehicles, equipped with a left side cargo door, and originally sold or currently registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin, and the District of Columbia. Water and road contaminants may become trapped in the protective conduit that covers the fuel filler pipe and may cause the pipe to corrode.

Component:FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP

Potential Consequence

Significant corrosion may allow fuel to leak during refueling, and in the presence of an ignition source; there is an increased risk of fire.

Remedy

GM will notify owners, and dealers will install a new fuel filler neck, free of charge. The safety recall began on October 1, 2012. Owners may contact the Chevrolet owner center at 1-866-694-6546 and GMC at 1-866-996-9463.

Contact authorized dealer for service

EXTERIOR LIGHTING

Invalid DateNHTSACampaign: 78683

Summary

SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

Component:EXTERIOR LIGHTING

Potential Consequence

DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

Remedy

SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.

Contact authorized dealer for service

Seats And Restraints

Apr 10, 2008Transport CanadaCampaign: 2008120

Summary

Certain full-size passenger, cargo and cutaway vans may have front and rear seat belt buckles that will not latch or will not unlatch. There are two conditions that render the buckle inoperative after customer usage. Specifically, (1) with a damaged ejector hood, the latch tongue cannot fully enter the buckle and will not latch, and (2) if the release bar moves permanently out of position the buckle will either be unable to engage the latch or the pushbutton will be unable to unlatch the buckle. Correction: Dealers will inspect buckles and, if found to be inoperative, the entire buckle assembly will be replaced. Note: This is an expansion of recall 2005390.

Units Affected:106
Contact authorized dealer for service

SEAT BELTS

Invalid DateNHTSACampaign: 56836

Summary

ON CERTAIN FULL-SIZE PASSENGER, CARGO, OR CUTAWAY VANS, THE FRONT AND REAR SEAT BELT BUCKLES WILL NOT LATCH OR WILL NOT UNLATCH.

Component:SEAT BELTS

Potential Consequence

IN THE EVENT OF A CRASH, A SEAT OCCUPANT MAY NOT BE PROPERLY RESTRAINED INCREASING THE RISK OF PERSONAL INJURY.

Remedy

DEALERS WILL INSPECT THE BUCKLES AND, IF FOUND TO BE INOPERATIVE, THE ENTIRE BUCKLE ASSEMBLY WOULD BE REPLACED. FOR BUCKLES FOUND TO BE OPERATIVE, DEALER WILL REPLACE ONLY THE UPPER BUCKLE COVER. THE RECALL WILL BE CONDUCTED IN PHASES. THE FIRST PHASE MAILING BEGAN DURING MARCH 2006. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 OR GMC AT 1-866-996-9463.

Contact authorized dealer for service

Seats And Restraints

Dec 14, 2005Transport CanadaCampaign: 2005390

Summary

Certain full-size passenger, cargo and cutaway vans may have front and rear seat belt buckles that will not latch or will not unlatch. There are two conditions that render the buckle inoperative after customer usage. Specifically, (1) with a damaged ejector hood, the latch tongue cannot fully enter the buckle and will not latch, and (2) if the release bar moves permanently out of position the buckle will either be unable to engage the latch or the pushbutton will be unable to unlatch the buckle. Correction: Dealers will inspect buckles and, if found to be inoperative, the entire buckle assembly will be replaced.

Units Affected:39
Contact authorized dealer for service

Other

Jul 7, 2004Transport CanadaCampaign: 2004216

Summary

On certain vehicles, the transmission shift cable may allow the transmission indicator (PRNDL) to indicate a different gear selected than the transmission is in. If this condition occurred while a vehicle is resting on an uneven surface, the vehicle could roll away after the driver has exited. Correction: Dealer will inspect and replace the transmission shift cable assembly.

Units Affected:521
Contact authorized dealer for service

SEAT BELTS:FRONT:ANCHORAGE

Invalid DateNHTSACampaign: 50230

Summary

CERTAIN EXTENDED AND REGULAR CAB PICKUP TRUCKS AND CARGO VANS CONVERTED TO COMPRESSED NATURAL GAS (CNG) FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 225, 'CHILD RESTRAINT ANCHORAGE SYSTEMS.' THESE VEHICLES HAVE ONE SEATING POSITION, THE CENTER REAR SEAT, EQUIPPED WITH CHILD RESTRAINT LOWER ANCHORAGES.

Component:SEAT BELTS:FRONT:ANCHORAGE

Potential Consequence

THE STANDARD REQUIRES CHILD SEAT LOWER ANCHORAGES IN TWO SEATING POSITIONS FOR VEHICLES WITH THREE REAR SEATING POSITIONS. THE STANDARD CAB AND CARGO VAN VEHICLES, WHICH ONLY HAVE FRONT SEATING POSITIONS, HAVE AN AIR BAG OFF SWITCH TO DISABLE THE FRONT PASSENGER AIR BAG AND DO NOT HAVE CHILD RESTRAINT LOWER ANCHORAGES IN THE PASSENGER SEAT. THE STANDARD REQUIRES PASSENGER SEAT CHILD SEAT LOWER ANCHORAGES IN VEHICLES WITH AN AIR BAG OFF SWITCH. HOWEVER, THE STANDARD DOES NOT REQUIRE VEHICLES WITH ONLY FRONT SEATING POSITIONS TO HAVE LOWER ANCHORAGE PROVISIONS IF THE VEHICLE IS NOT EQUIPPED WITH AN AIR BAG OFF SWITCH.

Remedy

TO BRING THE STANDARD CAB AND CARGO VAN VEHICLES INTO COMPLIANCE, DEALERS WILL INJECT EPOXY INTO THE AIR BAG OFF SWITCH TO PREVENT AIR BAG ACTIVATION, RELOCATE THE SWITCH BEHIND THE INSTRUMENT PANEL AND THEN INSTALL A COVER OVER THE RESULTING OPENING. THE SUN VISOR LABEL AND OWNER'S MANUAL WILL ALSO BE CHANGED. THE CORRECTION FOR THE EXTENDED CAB VEHICLE WILL CONSIST OF CHANGING THE FRONT PASSENGER SEAT TO A SEAT THAT HAS CHILD RESTRAINT LOWER ANCHORAGES. THE RECALL BEGAN ON SEPTEMBER 9, 2004. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438 OR GMC AT 1-866-996-9463.

Contact authorized dealer for service

SERVICE BRAKES, HYDRAULIC

Invalid DateNHTSACampaign: 52180

Summary

CERTAIN SPORT UTILITY VEHICLES, PICKUP TRUCKS, AND PASSENGER VANS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 135, ?PASSENGER CAR BRAKE SYSTEMS.? SOME OF THESE VEHICLES WERE PRODUCED WITH AN OUT-OF-SPECIFICATION BRAKE HYDRO-BOOST HOUSING RELIEF VALVE BORE.

Component:SERVICE BRAKES, HYDRAULIC

Potential Consequence

CONSEQUENTLY, THE VALVE O-RING SEAL MAY FRACTURE. STEERING EFFORTS MAY BE SLIGHTLY INCREASED WHILE BRAKING OR PARKING. UNDER CERTAIN DRIVING CONDITIONS, A FRACTURED SEAL MAY REQUIRE A SLIGHT INCREASE IN THE APPLIED BRAKE PEDAL EFFORT TO ACHIEVE THE SAME VEHICLE DECELERATION RATE AS PRIOR TO THE SEAT FRACTURE.

Remedy

DEALERS ARE TO REPLACE THE HYDRO-BOOST RELIEF VALVE. THE RECALL BEGAN ON JUNE 18, 2004. OWNERS SHOULD CONTACT CADILLAC AT 1-866-982-2339; CHEVROLET AT 1-800-630-2438; GMC AT 1-866-996-9463; OR HUMMER AT 1-866-486-6376.

Contact authorized dealer for service

Brakes

Jan 29, 2004Transport CanadaCampaign: 2004037

Summary

On certain vehicles, the relief valve o-ring seal within the brake hydro-boost module could fail. If this happens during braking applications, the driver may be able to hear an engine compartment noise similar to the sound that occurs when the steering wheel is turned to a full stop position. The driver could also experience a slight increase in steering efforts while braking and parking. Under certain driving conditions, a slight increase in the applied brake pedal effort may be required to achieve the same vehicle deceleration rate as prior to the seal failure. Correction: Dealers will inspect the hydro-boost module, and replace it, if necessary.

Units Affected:4
Contact authorized dealer for service

Visual System

Nov 26, 2003Transport CanadaCampaign: 2003294

Summary

Certain vehicles do not comply with either CMVSS 105, or CMVSS 135. The red brake warning indicator will not be illuminated while the ABS is modulating the front brakes. Correction: Since this does not pose any safety risk, no corrective action is required.

Units Affected:27
Contact authorized dealer for service

EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL

Invalid DateNHTSACampaign: 47162

Summary

CERTAIN MINIVANS, PASSENGER AND SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEM." THE OWNER'S MANUAL DOES NOT EXPLAIN THE MEANING OF THE LOCATION SYMBOLS FOR THE CHILD RESTRAINT LOWER UNIVERSAL ANCHORAGE SYSTEM.

Component:EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL

Potential Consequence

THIS DOES NOT MEET THE REQUIREMENTS OF THE STANDARD.

Remedy

OWNERS WILL BE PROVIDED WITH A SUPPLEMENT FOR THEIR OWNER'S MANUAL. THIS SUPPLEMENT DESCRIBES AND SHOWS THE LOCATION SYMBOLS FOR THE CHILD RESTRAINT ANCHORS THAT ARE LOCATED IN THE VEHICLE AND ON THE CHILD RESTRAINT OR BOOSTER CUSHION. OWNER NOTIFICATION BEGAN AUGUST 18, 2003. OWNERS SHOULD CONTACT BUICK AT 1-866-608-8080, CADILLAC AT 1-866-982-2339, CHEVROLET AT 1-800-630-2438, GMC AT 1-866-996-9463, PONTIAC AT 1-800-620-7668, OR OLDSMOBILE AT 1-800-630-6537.

Contact authorized dealer for service

Seats And Restraints

Jul 16, 2003Transport CanadaCampaign: 2003172

Summary

Certain vehicles do not comply with CMVSS 225 and 210.2. The Owner's Manual does not include the location symbols for the Lower Universal Anchorage System for Restraint Systems and Booster Cushions and an explanation of the meaning of the symbols. Correction: Owner's will receive an Owner's Manual supplement.

Units Affected:54
Contact authorized dealer for service

Electrical

Jun 16, 2003Transport CanadaCampaign: 2003154

Summary

On certain vehicles, water may enter and corrode the rear licence plate lamp socket causing it to operate intermittently or not at all. The left rear tail lamp may also become inoperative. The temperature of the licence plate lamp socket could increase to the point that it may begin to soften and melt. If the socket assembly were to reach the point of melting, the occupants of the vehicle may notice an odor and smoke at the rear doors of the vehicle. If this odor and smoke were ignored, the plastic could ignite and a fire could occur. Correction: Dealer will install a new sealed rear licence plate lamp socket assembly.

Units Affected:5
Contact authorized dealer for service

EXTERIOR LIGHTING

Invalid DateNHTSACampaign: 47303

Summary

CERTAIN VANS HAVE A CONDITION IN WHICH WATER MAY ENTER AND CORRODE THE REAR LICENSE PLATE LAMP SOCKET. IF THE LAMP SOCKET WERE TO CORRODE, THE REAR LICENSE PLATE LAMP MAY OPERATE INTERMITTENTLY OR NOT AT ALL, AND THE LEFT REAR TAIL LAMP MAY BECOME INOPERATIVE. THE TEMPERATURE OF THE LICENSE PLATE LAMP SOCKET COULD INCREASE TO THE POINT THAT IT MAY BEGIN TO SOFTEN AND MELT.

Component:EXTERIOR LIGHTING

Potential Consequence

IF THE SOCKET ASSEMBLY WERE TO REACH THE POINT OF MELTING, THE OCCUPANTS OF THE VEHICLE MAY NOTICE AN ODOR AND SMOKE AT THE REAR DOORS OF THE VEHICLE. IF THIS ODOR AND SMOKE WERE IGNORED, THE PLASTIC COULD IGNITE AND A FIRE COULD OCCUR.

Remedy

DEALERS WILL INSTALL A NEW SEALED REAR LICENSE PLATE LAMP SOCKET ASSEMBLY. OWNER NOTIFICATION BEGAN JULY 21, 2003. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782.

Contact authorized dealer for service

SEAT BELTS:FRONT:BUCKLE ASSEMBLY

Invalid DateNHTSACampaign: 48209

Summary

ON CERTAIN VANS WITH A GROSS VEHICLE WEIGHT OF LESS THAN 8,500 POUNDS, DURING A VEHICLE CRASH SUFFICIENT ENOUGH TO DEPLOY THE SAFETY BELT PRETENSIONER, THE FRONT SAFETY BELT BUCKLES MAY NOT RELEASE AFTER THE VEHICLE CRASH, OR ALTERNATELY MAY EJECT THE SAFETY BELT LATCH DURING THE VEHICLE CRASH.

Component:SEAT BELTS:FRONT:BUCKLE ASSEMBLY

Potential Consequence

THIS COULD RESULT IN INCREASED RISK OF PERSONAL INJURY.

Remedy

DEALERS WILL REPLACE THE FRONT DRIVER AND PASSENGER SIDE SAFETY BELT BUCKLE. OWNER NOTIFICATION BEGAN JUNE 3, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782.

Contact authorized dealer for service

Seats And Restraints

Feb 19, 2003Transport CanadaCampaign: 2003040

Summary

On certain vehicles, the seat belt push button may not release the latch plate after the pretensioner is deployed, or alternately the seat belt latch plate may eject during a crash event with a pretensioner deployment. If an occupant was using the seat belt assembly and the latch plate ejected from the buckle assembly during pretensioner actuation, the seat belt assembly may not provide a desired level of occupant restraint. If an occupant was using the seat belt assembly and the push button became stuck in the buckle assembly during pretensioner actuation, pressing on the seat belt push button would not release the latch plate from the buckle to allow the belted occupant to exit the vehicle. Correction: Dealer will replace the front seat belt buckles.

Units Affected:1
Contact authorized dealer for service

STEERING:LINKAGES

Invalid DateNHTSACampaign: 45418

Summary

ON CERTAIN VANS WITH AN 8,500 LB. OR 8,600 LB. GROSS VEHICLE WEIGHT RATING, THE NUT ATTACHING THE PITMAN ARM TO THE STEERING LINKAGE MAY NOT BE TIGHTENED ADEQUATELY RESULTING IN A POSSIBLE SEPARATION.

Component:STEERING:LINKAGES

Potential Consequence

A SEPARATION COULD RESULT IN LOSS OF VEHICLE CONTROL, AND A CRASH COULD OCCUR WITH PRIOR WARNING.

Remedy

DEALERS WILL TIGHTEN THE PITMAN ARM NUT TO THE PROPER SPECIFICATION. IF THE NUT IS MISSING, THE DEALER WILL INSTALL A NEW NUT AND TIGHTEN IT CORRECTLY. OWNER NOTIFICATION BEGAN DECEMBER 10, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782.

Contact authorized dealer for service

STEERING:LINKAGES:TIE ROD ASSEMBLY

Invalid DateNHTSACampaign: 44232

Summary

ON CERTAIN VANS, THE RIGHT-HAND TIE ROD END NUT MAY NOT BE TIGHTENED ADEQUATELY. THE NUT CAN LOOSEN RESULTING IN SEPARATION OF THE TIE ROD FROM THE STEERING KNUCKLE.

Component:STEERING:LINKAGES:TIE ROD ASSEMBLY

Potential Consequence

SEPARATION OF A TIE ROD CAN CAUSE UNEXPECTED VEHICLE STEERING IN SOME MANEUVERS AND COULD CAUSE A CRASH WITHOUT PRIOR WARNING.

Remedy

DEALERS WILL TIGHTEN THE TIE ROD END NUT AND, IF NECESSARY, REPLACE THE TIE ROD END. OWNER NOTIFICATION BEGAN NOVEMBER 27, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782.

Contact authorized dealer for service

Steering

Dec 12, 2002Transport CanadaCampaign: 2002237

Summary

On certain 2500 and 3500 series vans, the nut attaching the pitman arm to the steering linkage may not be torqued to specification, which could lead to a possible separation. A separation could result in loss of vehicle control, and a crash could occur without prior warning. Correction: Dealer will torque the nut to proper specifications.

Units Affected:479
Contact authorized dealer for service

Steering

Nov 22, 2002Transport CanadaCampaign: 2002225

Summary

On certain vehicles, the right-hand tie rod end nut may not have been torqued to specification and could loosen, resulting in separation of the tie rod. This could cause unexpected steering input and could cause a crash without prior warning. Correction: Dealers will torque the tie rod end nut to specs.

Units Affected:930
Contact authorized dealer for service

WHEELS:LUGS/NUTS/BOLTS/STUDS

Invalid DateNHTSACampaign: 44401

Summary

CERTAIN VANS WERE BUILT WITHOUT A WHEEL BEARING ASSEMBLY RETAINING NUT, WHICH COULD LEAD TO A POSSIBLE BEARING SEPARATION.

Component:WHEELS:LUGS/NUTS/BOLTS/STUDS

Potential Consequence

IF THIS WERE TO OCCUR, THE AMBER-COLORED ABS TELL-TALE LAMP IN THE INSTRUMENT PANEL WOULD ILLUMINATE AND THE ABS SYSTEM WOULD BE DISABLED. THE DRIVER WOULD ALSO NOTICE A GRINDING NOISE, A DECREASE IN THE VEHICLE SPEED, AND THE STEERING WILL PULL IN THE DIRECTION OF THE AFFECTED BRAKE ASSEMBLY. THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.

Remedy

DEALERS WILL INSPECT THE WHEEL BEARING ASSEMBLY. IF THE INSPECTION REVEALS A MISSING RETAINING NUT, THE WHEEL BEARING ASSEMBLY WILL BE REPLACED. OWNER NOTIFICATION BEGAN NOVEMBER 13, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782.

Contact authorized dealer for service

Suspension

Nov 15, 2002Transport CanadaCampaign: 2002211

Summary

On certain 2500 and 3500 series vehicles, a wheel bearing assembly retaining nut was omitted during assembly, which could lead to a possible bearing separation. If this were to occur, the ABS warning lamp would illuminate and the ABS system would be disabled. The driver would also notice a grinding noise, a decrease in vehicle speed and a steering pull in the direction of the affected assembly. Failure to heed these warnings can result in loss of vehicle control and a crash. Correction: Dealers will inspect and replace the wheel bearing assembly if a missing nut is noted during inspection.

Units Affected:1
Contact authorized dealer for service

Generated by Cardog • December 11, 2025

2003 Chevrolet Express

Safety Recalls & Notices

Total
24
safety notices
Units
3,143
vehicles affected
Recent
Apr 6, 2023
last notice date

24 Active Recalls

Requires attention

Recent Activity
2023
1 recall
2012
2 recalls
2009
1 recall
Cardog App Icon

Get the Cardog App

Access your vehicle valuations, market insights, and car research tools on the go. Available for both iOS and Android devices.

Download app
Important Notice
Contact your dealer to verify recalls for your specific VIN and schedule service.