2001 Echo

Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.

2021723 · 55,683 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

ON CERTAIN PASSENGER VEHICLES, DUE TO IMPROPER MOLDING OF THE RESIN BODY OF THE CRANKSHAFT POSITION SENOR INSTALLED ON THE ENGINE BLOCK, ENGINE OIL MAY PENETRATE THE SEAL AND ENTER THE SENSOR WIRING CONNECTOR. THE WIRE HARNESS CONNECTOR MAY NOT BE SUFFICIENTLY ATTACHED TO THE LOCKING TAB OF THE SENSOR WIRING CONNECTOR.

06V266000 · 34,771 units in campaign · NHTSA

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

On certain vehicles, improper manufacturing of the Crankshaft Position Sensor body could cause engine oil to penetrate the seal and enter the sensor wiring connector. In addition, the wire harness connector may not be sufficiently attached to the locking tab of the sensor wiring connector. Engine oil inside the sensor wiring connector could cause expansion due to the heat of the engine and could deform the sensor wiring connector. In the worst case, the connector may become disconnected, which could cause the engine to stall while driving and not be able to be restarted. Correction: Dealers will replace the Crankshaft Position Sensor.

2006181 · 14,975 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

On certain vehicles driven under repeated start and stop operation in extremely low ambient temperatures and in deep snow, there is a possibility that snow may accumulate in large quantities inside the rear wheel and freeze. Due to the shape of the rear brake tubes, the snow frozen inside the wheel may contact the rear brake tube during wheel rotation. In the worst case, if this condition occurs frequently, the rear brake tube could be damaged, which could result in leakage of brake fluid, causing a decrease in brake effectiveness. Correction: Dealers will replace the rear brake tubes.

2002179 · 27,351 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

ON CERTAIN PASSENGER VEHICLES, IF THE VEHICLE IS DRIVEN UNDER REPEATED START AND STOP OPERATION IN LOW AMBIENT TEMPERATURES AND IN DEEP SNOW, THERE IS A POSSIBILITY THAT SNOW COULD ACCUMULATE IN LARGE QUANTITIES INSIDE THE REAR WHEEL AND FREEZE. THE SNOW FROZEN INSIDE THE WHEEL COULD CONTACT THE REAR BRAKE LINE DURING WHEEL ROTATION.

02V268000 · 59,394 units in campaign · NHTSA

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer