2008 Endeavor

Certain vehicles, operated in areas where road salts are frequently used in winter, may be exposed to road debris (mud) mixed with road salt. This material can become trapped between a reinforcing bracket and the fuel filler pipe, potentially causing corrosion. Over time, corrosion could create a leak in the fuel filler pipe that could result in fuel leakage when fueling the vehicle. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will replace the fuel filler pipe of vehicles equipped with the first-generation version. Vehicles assembled with the second-generation filler pipe will be inspected and, if severe corrosion on the fuel filler pipe is observed, the pipe will be replaced with a third-generation version. For vehicles where corrosion of the fuel filler pipe is not observed, an anti-corrosion wax-like material will be applied to the filler pipe, and the inner wheel well shield will be replaced with an updated part that provides improved protection against mud intrusion and accumulation. ** Note: This recall supersedes recall 2010050.**

2011012 · 4,969 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

On certain vehicles, the software programming in the Heating, Ventilation, Air Conditioning (HVAC) controller may allow a combination of numerous data inputs to temporarily overload the calculation capacity of the controller, resulting in incorrect signals to be transmitted to the heater case mode door. This may cause the mode door to move to unselected positions during heater operation until the controller recovers and returns to proper operation. Over time, this excessive movement may damage the mode door shaft. These conditions could affect defroster performance, resulting in delayed clearing of the windshield, which could compromise safe vehicle operation and increase the risk of a crash. Correction: Dealers will replace the HVAC controller assembly, inspect the mode-door shaft for possible damage, and repair the mode-door shaft if necessary.

2010362 · 797 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

MITSUBISHI IS RECALLING CERTAIN MODEL YEAR 2006-2008 ENDEAVOR WITH MANUAL AIR CONDITIONING. DUE TO AN INCORRECT HEATER (HVAC) CONTROLLER SIGNAL, THE AIR FLOW FROM THE AIR VENTS MAY RANDOMLY CHANGE DIRECTION AND/OR THE TEMPERATURE MAY BRIEFLY CYCLE BETWEEN HOT AND COLD.

10V514000 · 19,410 units in campaign · NHTSA

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

MITSUBISHI IS RECALLING CERTAIN MODEL YEAR 2004-2010 ENDEAVOR VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, KENTUCKY, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, VIRGINIA, WEST VIRGINIA, WISCONSIN, AND WASHINGTON D.C. COLD STATES INCLUDE NORTH DAKOTA, SOUTH DAKOTA, NEBRASKA, KANSAS, OKLAHOMA, COLORADO, WYOMING, MONTANA, IDAHO, WASHINGTON, OREGON, AND UTAH. ADJOINING STATES INCLUDE ARKANSAS, TENNESSEE, AND NORTH CAROLINA. IN SEVERE CORROSIVE ENVIRONMENTS WHERE ROAD SALTS ARE FREQUENTLY USED IN WINTER VEHICLES MAY BE EXPOSED TO ROAD DEBRIS (MUD) MIXED WITH ROAD SALT. THIS MATERIAL CAN BECOME TRAPPED BETWEEN A REINFORCING BRACKET AND THE FUEL FILLER PIPE, POTENTIALLY CAUSING CORROSION. OVER TIME, CORROSION COULD CREATE A LEAK IN THE FUEL FILLER PIPE THAT COULD RESULT IN A FUEL LEAKAGE WHEN FUELING THE VEHICLE.

10V065000 · 108,147 units in campaign · NHTSA

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

MITSUBISHI IS RECALLING 120,000 MY 2004-2006 ENDEAVOR PASSENGER VEHICLES. DURING VEHICLE USE, THE IGNITION KEY INTERLOCK CABLE (WHICH IS A COMPONENT OF THE INTERLOCK SYSTEM) MAY ALLOW THE INTERLOCKING CAM TO FALL FORWARD AND ALLOW THE IGNITION KEY TO BE REMOVED FROM THE IGNITION SWITCH WHEN THE GEARSHIFT MECHANISM IS NOT IN THE PARK POSITION.

08V139000 · 116,600 units in campaign · NHTSA

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

On certain vehicles, the ignition key interlock cable may allow the interlocking cam to fall forward and allow the ignition key to be removed from the ignition when the gearshift mechanism is not in the PARK position. If the driver does not shift to PARK before removing the key, and fails to engage the parking brake, the vehicle could roll and a crash could occur. This could result in property damage, personal injury or death. Correction: Dealers will affect repairs.

2008100 · 4,353 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer