2006 Mazda Tribute
Safety Recalls & Notices
6 Active Recalls
Requires attention
SUSPENSION:FRONT:WHEEL BEARING
Summary
The Timken Company (Timken) is recalling certain aftermarket front wheel bearings, part number 510072, sold from January 22, 2015, to May 21, 2015, to be used as service parts on 2001-2012 Ford Escape, 2001-2011 Mazda Tribute, and 2005-2011 Mercury Mariner vehicles. The affected wheel bearings have incorrect dimensions of a 42mm bore, 76mm outer dimension, and 39mm width, instead of a 42mm bore, 78mm outer dimension and a 45mm width.
Potential Consequence
Use of an incorrectly sized wheel bearing can adversely affect the braking and steering of the vehicle, increasing the risk of a crash.
Remedy
Timken has begun notifying distributors who will offer purchasers replacement wheel bearings, free of charge. The recall began on May 21, 2015. Owners may contact Timken customer service at 1-866-984-6536.
Other
Summary
On certain vehicles equipped with a 3.0L V6 engine and speed control, inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. A stuck throttle may result in very high vehicle speeds and make it difficult to slow or stop the vehicle if the transmission is not shifted into neutral. This could result in a crash causing property damage and/or personal injury. Correction: Dealers will replace the rear engine cover fastener, which will raise the cover in the area of the speed control cable to provide adequate clearance between the cover the speed control cable connector.
ENGINE AND ENGINE COOLING
Summary
Mazda is recalling certain model year 2001 through 2006, and 2008, Tribute vehicles equipped with 3.0L V6 engines and speed control. Inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. This risk exists regardless of whether or not speed control (cruise control) is used.
Potential Consequence
A stuck throttle may result in very high vehicle speeds and make it difficult to stop or slow the vehicle, which could cause a crash, serious injury or death.
Remedy
Mazda will notify owners, and dealers will repair the vehicles by increasing the engine cover clearance, free of charge. Remedy parts are now available. The safety recall began on September 13, 2012. Owners may contact Mazda Customer Assistance Center at 1-800-222-5500, option #6.
VEHICLE SPEED CONTROL:CABLES
Summary
Mazda is recalling certain model year 2001 through 2006, and 2008, Tribute vehicles equipped with 3.0L V6 engines and speed control. Inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. This risk exists regardless of whether or not speed control (cruise control) is used.
Potential Consequence
A stuck throttle may result in very high vehicle speeds and make it difficult to stop or slow the vehicle, which could cause a crash, serious injury or death.
Remedy
Mazda will notify owners, and dealers will repair the vehicles by increasing the engine cover clearance, free of charge. Remedy parts are now available. The safety recall began on September 13, 2012. Owners may contact Mazda Customer Assistance Center at 1-800-222-5500, option #6.
VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR
Summary
ON CERTAIN TRUCKS AND SPORT UTILITY VEHICLES, THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE APPLIED TO THE OUTPUT SHAFT GEAR.
Potential Consequence
AFTER A PERIOD OF CONTINUOUS USE ON THE HIGH SPEED SETTING, LACK OF GREASE ON THE OUTPUT SHAFT GEAR MAY CAUSE THE GEAR TEETH TO DISTORT OR FRACTURE DURING OPERATION RESULTING IN THE LOSS OF WIPER FUNCTION. INOPERATIVE WIPERS UNDER INCLEMENT WEATHER CONDITIONS COULD CAUSE A CRASH DUE TO IMPAIRED VISIBILITY.
Remedy
DEALERS WILL INSPECT THE WIPER MOTOR FOR THE PRESENCE OF GREASE AND GREASE THE WIPER MOTOR GEARS IF NECESSARY. THE RECALL BEGAN ON NOVEMBER 28, 2005. OWNERS MAY CONTACT MAZDA AT 1-800-222-5500.
Other
Summary
On certain vehicles, the windshield wiper motor may have been produced without grease applied to the output shaft gear. After a period of continuous use on the high-speed setting, lack of grease may cause the gear teeth to distort and/or fracture during operation, resulting in the loss of wiper function. Correction: Dealers will inspect and, if required, apply grease to the output shaft gear.
Generated by Cardog • December 10, 2025
2006 Mazda Tribute
Safety Recalls & Notices
6 Active Recalls
Requires attention
