2003 Mazda Mpv
Safety Recalls & Notices
8 Active Recalls
Requires attention
Engine
Summary
Certain vehicles previously updated following an emission recall concerning the PCV hose may experience throttle icing during cold weather operation. As a result of misrouting of the PCV hose during the emission recall, moisture build-up inside the hose could freeze while the vehicle is parked. If the vehicle is then driven at constant highway speeds in extremely cold temperatures (-30 degrees Celsius or colder), the moisture in the blow-by gases may freeze in the throttle valve area. Under these conditions, even if the accelerator pedal is released while driving, engine speed may not decrease. Unwanted acceleration could result in a vehicle crash without prior warning. Correction: Dealers will inspect the previously replaced PCV hose for proper routing and reroute if necessary.
Other
Summary
On certain vehicles, the liftgate stay dampers and stud bolts may rust and stick together, causing the stud bolds to break off. In the worst case, this condition may allow the liftgate to suddenly drop during opening or closing, injuring the operator. Correction: Dealers will replace the left and right dampers and stud bolts.
EQUIPMENT:OTHER:LABELS
Summary
THE TIRE INFLATION PRESSURE INDICATED ON THE VEHICLE CERTIFICATION LABEL IS NOT CORRECT. THE LABELS SHOW THE MAXIMUM TIRE PRESSURE AS 240 KPA/32 PSI WHEN IT SHOULD BE SHOWN AS 240 KPA/35 PSI. AS A RESULT OF THIS ERROR, THE LOAD RATIOS FOR THE 205/65R15 94H AND THE 215/60R16 95H TIRES EXCEED THE LEVELS PERMITTED BY FMVSS 120.
Potential Consequence
IF THE TIRE IS OPERATED IN AN UNDER-INFLATED CONDITION, THE LOAD CARRYING CAPACITY OF THE VEHICLE MAY BE COMPROMISED, INCREASING THE RISK OF A CRASH.
Remedy
OWNERS WILL BE PROVIDED WITH A CORRECTED LABEL THAT THEY CAN APPLY TO THEIR VEHICLE, OR THEY CAN HAVE A DEALER INSTALL THE LABEL, IF DESIRED. THE RECALL BEGAN ON JULY 16, 2004. OWNERS SHOULD CONTACT MAZDA AT 1-800-222-5500, OPTION #4.
EQUIPMENT:OTHER:LABELS
Summary
CERTAIN MINIVANS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." SOME OF THESE VEHICLES WERE PRODUCED WITH AIR BAG WARNING LABELS INTENDED FOR THE CANADIAN MARKET. THUS, THE LABELS CONTAIN WARNINGS IN BOTH ENGLISH AND FRENCH. AS A RESULT, THE AREA OF THE ENGLISH WARNING IS ONLY 16 SQUARE CENTIMETERS, AS OPPOSED TO THE 30 SQUARE CENTIMETERS REQUIRED BY THE STANDARD.
Remedy
OWNERS WILL BE PROVIDED WITH AIR BAG CAUTION LABELS AND INSTALLATION INSTRUCTIONS WHICH WERE MAILED ON JULY 22, 2004. OWNERS SHOULD CONTACT MAZDA AT 1-800-222-5500.
Airbag
Summary
On certain vehicle, the airbag warning labels on the sun visors are English only. This does not comply with the requirements of CMVSS 208. Correction: Mazda will mail owners corrected replacement labels and installation instructions.
EXTERIOR LIGHTING:FOG LIGHTS
Summary
ON CERTAIN MINI VANS AND PASSENGER VEHICLES, THE SOCKET HOLDER IN THE FOG LIGHTS IS INSTALLED IN THE LAMP CASING USING PRESSURE. DURING OPERATION OF THE FOG LIGHT, THE HEAT FROM THE BULB CAN EXPAND THE SOCKET HOLDER. THE EXPANSION CAN FORCE THE SOCKET HOLDER REARWARD. AFTER REPEATEDLY BEING SUBJECT TO THIS EXPANSION, IF THE FOG LIGHT IS ALSO SUBJECTED TO VIBRATION DURING VEHICLE OPERATION, THE SOCKET HOLDER WITH THE BULB HOLDER AND THE WIRING HARNESS MAY SEPARATE FROM THE FOG LIGHT CASING.
Potential Consequence
SHOULD THIS OCCUR, THE BULB SOCKET AND THE HARNESS CAN DROP INSIDE THE BUMPER AND POSSIBLY BUT RARELY, THE HEAT GENERATED BY THE BULB CAN CAUSE THE BUMPER TO BURN.
Remedy
DEALERS WILL INSTALL A SPRING TO PREVENT THE SOCKET HOLDER FROM SEPARATING FROM THE LAMP CASE. OWNER NOTIFICATION BEGAN ON JULY 14, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MAZDA AT 1-800-222-5500.
Electrical
Summary
On certain vehicles, the front fog light bulb socket was installed improperly. If the vehicle continues to operate with this condition, the bulb socket and the wiring harness may separate from the fog light housing as a result of exposure to vehicle vibration. Should this occur, the bulb socket and the harness can drop inside the bumper and in the worst case, the heat generated can cause the bumper to burn. Correction: Dealer will re-install the bulb socket properly.
EXTERIOR LIGHTING:FOG LIGHTS
Summary
ON CERTAIN MINI VANS EQUIPPED WITH FRONT FOG LIGHTS,THE FOG LIGHT BULB SOCKET MAY HAVE BEEN INSTALLED IMPROPERLY.
Potential Consequence
IF THE VEHICLE CONTINUES TO BE USED WITH THIS CONDITION, THE BULB SOCKET AND THE WIRING HARNESS MAY SEPARATE FROM THE FOG LIGHT HOUSING IF EXPOSED TO SHOCK AND/OR VIBRATION AND DROP INSIDE THE BUMPER. SHOULD THIS OCCUR, THE OPERATION OF THE FOG LIGHT MAY THEN CAUSE THE BUMPER TO BURN.
Remedy
DEALERS WILL INSPECT THE INSTALLATION CONDITION OF THE FOG LIGHT BULB ASSEMBLY, AND REPAIR IT WHEN NECESSARY. OWNER NOTIFICATION BEGAN MARCH 31, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MAZDA AT 1-800-222-5500.
Generated by Cardog • December 10, 2025
2003 Mazda Mpv
Safety Recalls & Notices
8 Active Recalls
Requires attention
