Safety Recalls & Notices
Requires attention
Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 210.1 - User-ready Tether Anchorages for Restraint Systems. Specifically, the pictograms identifying the location of the tether anchors measure 15 mm in height instead of 20 mm as required by the Standard. Correction: Since this non-compliance condition does not pose any safety risk, no corrective action is required.
On certain vehicles the Intelligent Power Distribution Module (IPDM) assembly contains an Engine Control Module (ECM) relay that has a diode for electrical current noise reduction. The ECM relay may allow silicon vapor to form and over time the silicon evaporates from the diode molding which causes silicon oxide to develop on the ECM relay contact due to arcing. In certain instances, this oxidation could cause engine performance issues (hesitation, rough engine idle, slow start/no-start condition), and engine stalling at low engine speeds which may result in a crash. Correction: Dealers will replace the Engine Control Module (ECM) relay.
NISSAN IS RECALLING CERTAIN MODEL YEAR 2004-2006 ARMADA, TITAN, INFINITI QX56 AND MODEL YEAR 2005-2006 FRONTIER, PATHFINDER AND XTERRA VEHICLES. THE INTELLIGENT POWER DISTRIBUTION MODULE (IPDM) ASSEMBLY CONTAINS AN ENGINE CONTROL MODULE (ECM) RELAY THAT HAS A DIODE FOR ELECTRICAL CURRENT NOISE REDUCTION. THE ECM RELAY MAY ALLOW SILICON VAPOR TO FORM AND, OVER TIME, THE SILICON EVAPORATES FROM THE DIODE MOLDING WHICH CAUSES SILICON OXIDE TO DEVELOP ON THE ECM RELAY CONTACT DUE TO ARCING.
THIS COULD CAUSE ENGINE STALLING INCREASING THE RISK OF A CRASH.
DEALERS WILL REPLACE THE ECM RELAY INSIDE THE IPDM ASSEMBLY. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 6, 2010. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.
NISSAN IS RECALLING CERTAIN FRONT AND REAR LOWER LINKS, P/NOS. 54501ZQ00A, 54500ZQ00A, 551A1ZQ00A, 551A0ZQ00A , 54501EA00A, 54500EA00A, 551A1EA500, 551A0EA500, 54501ZR00A, AND 54500ZR00A, SOLD BETWEEN NOVEMBER 25, 2009 AND MAY 14, 2010 AS REPLACEMENT PARTS FOR MODEL YEAR 2004 THROUGH 2010 TITAN, ARMADA, AND QX56, AND MODEL YEARS 2005 THROUGH 2010 FRONTIER, XTERRA, AND PATHFINDER VEHICLES. THE LOWER CONTROL LINK ASSEMBLY HAS TWO CYLINDRICAL COLLARS FORMING THE INBOARD ATTACHMENT POINTS TO THE CHASSIS. DUE TO AN IMPROPER WELDING PROCESS SOME COLLARS MAY CONTAIN WELDS THAT DO NOT MEET STRENGTH SPECIFICATIONS.
IF THE COLLAR WELD SEPARATES, THE VEHICLE HANDLING WILL DETERIORATE, POSSIBLY RESULTING IN A VEHICLE CRASH.
NISSAN WILL NOTIFY OWNERS AND DEALERS WILL REPLACE ANY AFFECTED LOWER LINK FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JULY 12, 2010. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.
Certain 2005-2006 model year vehicles may have been assembled with an incorrectly manufactured air conditioning condenser fan motor, which could allow excessive water intrusion and inadequate drainage. If sufficient moisture accumulates in the motor, corrosion could occur, increasing internal friction, and thereby augmenting the electrical current draw. This could cause an increase in the motors operating temperature that could eventually melt its wiring insulation and other plastic components and form a gas. If two wires without insulation touch each other and create a spark, this gas could ignite and result in a vehicle fire, which could cause property damage, personal injury or death. Note: 2004, and some 2005 model year vehicles are equipped with a different fan motor that is not subject to this campaign. However, it is possible that a limited number of these vehicles may have received the subject condenser fan as a service replacement part, thereby being included in this action. Correction: Dealers will affect repairs.
Generated by Cardog • December 14, 2025
Safety Recalls & Notices
Requires attention