On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, could eventually degrade the propellant contained in the passenger frontal airbag. This could cause the airbag to deploy with more force than normal. As a result, if the vehicle were involved in a collision that warrants airbag deployment, fragments could be propelled toward vehicle occupants, and the airbag assembly could be damaged, preventing proper function. These issues could increase the risk of injury. Correction: Depending on the vehicle model, dealers will either replace the passenger frontal airbag inflator, or replace the airbag assembly. Note: Canadian climate results in the propellant degrading slowly. The recall is being conducted as a precaution to address future risk, and is expected to replace airbag inflators before their function would be affected. Additional note: The 2010 model year vehicles involved in this campaign have been identified as having once being registered in “Zone B” in the USA.

2018016 · 21,632 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

General Motors Canada is conducting a voluntary Safety Improvement Program involving the passenger airbag inflator in certain vehicles that were originally sold or ever registered in certain high humidity areas of the United States equipped with Takata airbags. General Motors will replace the passenger inflator on affected vehicles, depending on the vehicle involved. Owners who believe their vehicles may have been originally purchased or registered in the states of New Jersey, Delaware, District of Columbia, Maryland, Pennsylvania, Ohio, Indiana, Illinois, Virginia, West Virginia, Kentucky, Missouri, Nebraska, Kansas, Oklahoma, Arkansas, Tennessee, North Carolina, Nevada, Arizona, New Mexico, California, Texas, Louisiana, Mississippi, Alabama, Georgia, South Carolina, Florida, Hawaii, Puerto Rico or the U.S. Virgin Islands should contact a General Motors dealer. This action is not being conducted under the requirements of the Motor Vehicle Safety Act. Note: This Safety Improvement Campaign is superseded by recall 2018-016 (GM Recall 17476). Please see <a href="http://wwwapps.tc.gc.ca/Saf-Sec-Sur/7/VRDB-BDRV/search-recherche/detail.aspx?lang=eng&&rn=2018016">recall 2018016</a> for more information.

2017134 · 150 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

On certain vehicles, inconsistent application of grease during the manufacturing process could cause the driver's side power window master switch to stick or become inoperative due to electrical contact point wear. This could cause debris to accumulate between the contact points, potentially resulting in an electrical short circuit. If a short circuit occurs, the switch assembly may overheat, produce smoke, melt and/or potentially lead to a fire causing injury and/or property damage. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary. Note: This is an expansion of recall 2012-342.

2015496 · 8,751 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

On certain vehicles, electrical circuitry in the steering wheel assembly may become damaged. As a result, the driver's airbag may not function as intended, causing the instrument panel airbag warning lamp to illuminate. Failure of the driver's airbag to deploy during a crash (where deployment is warranted) could increase the risk of injury to the seat occupant. Correction: Dealers will replace the spiral cable assembly.

2014145 · 26,690 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

On certain vehicles, due to improperly applied grease, the driver's side power window master switch could stick or become inoperative. If attempts are made to lubricate the switch, the switch assembly could overheat and melt. A melting switch may produce smoke and potentially lead to a fire causing property damage and/or personal injury. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary.

2012342 · 16,724 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer

On certain vehicles, the accelerator pedal may become stuck in the wide open position due to an unsecured or incompatible driver's floor mat. A stuck open accelerator pedal may result in very high vehicle speeds and make it difficult to stop the vehicle, which could cause a crash, serious injury or death. Correction: Owners will be notified by first class mail to remove any unsecured driver's floor mat until further notice by the manufacturer.

2010034 · 28,488 units in campaign · Transport Canada

Applies only if the manufacturer confirms your VIN · repair by an authorized dealer