Newest first. Many cover only part of a model year, so check your VIN with NHTSA or Lexus before booking a repair.
NHTSA · listed for this model year
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2007-2010 Lexus LS vehicles manufactured May 9, 2006, to July 20, 2010, 2006-2011 Lexus GS vehicles manufactured January 6, 2005, to September 10, 2010, and 2006-2011 Lexus IS vehicles manufactured August 30, 2005, to September 10, 2010. Due to anti-corrosion plating remnants, fuel may leak from where the fuel pressure sensor is attached to the fuel delivery pipe.
A fuel leak in the presence of an ignition source increases the risk of a fire.
Toyota will notify owners, and dealers will clean and reseal the fuel pressure sensor mounting area, free of charge. The recall began March 3, 2015. Owners may contact Toyota customer service at 1-800-331-4331.
14V647000 · 422,509 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2006 AND 2007 LEXUS GS300 AND GS350 ALL WHEEL DRIVE (AWD) VEHICLES. THERE IS A POSSIBILITY THAT THE PLASTIC PAD EMBEDDED INTO THE FLOOR CARPET MAY INTERFERE WITH THE OPERATION OF THE ACCELERATOR PEDAL.
THE ACCELERATOR PEDAL COULD TEMPORARILY BECOME STUCK IN A PARTIALLY DEPRESSED POSITION RATHER THAN RETURN TO THE IDLE POSITION. A STUCK ACCELERATOR PEDAL MAY RESULT IN UNINTENDED AND SUSTAINED VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP INCREASING THE RISK OF A CRASH.
DEALERS WILL MODIFY THE PLASTIC PAD ON THE FLOOR CARPET FREE OF CHARGE. THE MANUFACTURER HAS NOT YET PROVIDED AN OWNER NOTIFICATION SCHEDULE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
11V115000 · 19,647 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2006-2009 LEXUS IS AND MODEL YEAR 2006-2007 LEXUS GS VEHICLES. DUE TO INSUFFICIENT TIGHTENING OF THE FUEL PRESSURE SENSOR CONNECTED TO AN ENGINE FUEL DELIVERY PIPE WITH NICKEL PHOSPHORUS PLATING, THERE IS A POSSIBILITY THAT, OVER TIME, THE PRESSURE SENSOR COULD LOOSEN. IF LOOSENING OCCURS, FUEL COULD LEAK PAST A GASKET USED IN THE CONNECTION BETWEEN THE SENSOR AND THE PIPE AND THROUGH THE THREADED PORTION OF THE SENSOR.
FUEL LEAKAGE, IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE.
DEALERS WILL INSPECT FOR FUEL LEAKAGE FROM THE THREADED PORTION OF THE FUEL PRESSURE SENSOR AND IF A FUEL LEAK IS NOT CONFIRMED, DEALERS WILL FURTHER TIGHTEN THE FUEL PRESSURE SENSOR WITH THE PROPER TORQUE. IF A FUEL LEAK IS CONFIRMED, THE GASKET BETWEEN THE SENSOR AND THE FUEL DELIVER PIPE WILL BE REPLACED WITH A NEW ONE, AND THE SENSOR WILL BE TIGHTENED WITH THE PROPER TORQUE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 7, 2011. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
11V029000 · 244,779 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2006 AVALON, MODEL YEAR 2004-2006 HIGHLANDER, MODEL YEAR 2004-2006 LEXUS RX, AND MODEL YEAR 2006 LEXUS GS AND IS VEHICLES. BRAKE FLUID CONTAINING POLYMERS IS USED THAT ACTS AS LUBRICANTS FOR CERTAIN BRAKE SYSTEM COMPONENTS. IF REPLACEMENT BRAKE FLUID IS USED THAT DOES NOT CONTAIN SUCH POLYMERS, OR THAT CONTAINS ONLY SMALL AMOUNTS, A PART OF THE RUBBER SEAL LOCATED AT THE REAR OF THE BRAKE MASTER CYLINDER MAY BECOME DRY, AND THE SEAL MAY CURL DURING MOVEMENT OF THE PISTON. IF THIS OCCURS, A SMALL AMOUNT OF BRAKE FLUID COULD SLOWLY LEAK FROM THE SEAL INTO THE BRAKE BOOSTER.
A LEAK OF BRAKE FLUID COULD LEAD TO A CHANGE IN BRAKE PEDAL FEEL AND OVERTIME A DEGRADATION IN BRAKING PERFORMANCE INCREASING THE RISK OF A CRASH.
DEALERS WILL REPLACE THE SEAL WITH A NEWLY DESIGNED ONE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 15, 2010. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331 AND LEXUS AT 1-800-255-3987.
10V499000 · 728,544 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
TOYOTA IS RECALLING 214,570 MY 2006-2008 LEXUS IS, MY 2006-2007 GS AND MY 2007-2008 LS PASSENGER VEHICLES EQUIPPED WITH ALUMINUM FUEL DELIVERY PIPES (FUEL RAILS). ETHANOL FUELS WITH A LOW MOISTURE CONTENT WILL CORRODE THE INTERNAL SURFACE OF THE FUEL RAILS. AS THIS CONDITION PROGRESSES, THE ENGINE MALFUNCTION INDICATOR LIGHT MAY ILLUMINATE.
OVER TIME, THE CORROSION MAY CREATE A PINHOLE RESULTING IN FUEL LEAKAGE. FUEL LEAKAGE, IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE.
DEALERS WILL INSPECT AND REPLACE THE FUEL DELIVERY PIPES FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING FEBRUARY 2009. OWNERS MAY CONTACT TOYOTA/LEXUS AT 1-800-255-3987.
09V020000 · 214,570 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
ON CERTAIN VEHICLES, HIGH STRESS AREAS MAY HAVE BEEN CREATED IN TWO SPECIFIC FUEL PIPES LOCATED IN THE ENGINE COMPARTMENT. COMBINED WITH OTHER FACTORS SUCH AS THE PRESENCE OF CORROSIVE AGENTS IN FUEL, A CRACK MAY FORM OVER TIME LEADING TO FUEL LEAKAGE FROM THE FUEL LINE(S).
FUEL LEAKAGE IN THE PRESENCE OF AN IGNITION SOURCE COULD RESULT IN A FIRE.
DEALERS WILL REPLACE THE TWO INVOLVED FUEL LINES WITH NEWLY DESIGNED LINES FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 15, 2007. OWNERS MAY CONTACT LEXUS AT 1-800-255-3987.
07V545000 · 34,343 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
ON CERTAIN PASSENGER VEHICLES, IF THE FRONT SEAT BELT RETRACTORS (BOTH DRIVER AND FRONT PASSENGER) BECOME LOCKED, THEY MAY NOT RELEASE DUE TO A COMPONENT OF THE EMERGENCY LOCKING SYSTEM. IF THE SEAT BELT IS LOCKED IN THIS CONDITION, THE OCCUPANT MAY NOT BE ABLE TO PROPERLY FASTEN THE SEAT BELT.
AN OCCUPANT NOT PROPERLY WEARING A SEAT BELT MAY HAVE AN INCREASED RISK OF INJURY DURING A CRASH.
DEALERS WILL REPLACE THE FRONT SEAT BELT ASSEMBLIES. THE RECALL BEGAN ON APRIL 21, 2006. OWNERS MAY CONTACT LEXUS AT 1-800-255-3987.
06V121000 · 28,947 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
ON CERTAIN VEHICLES, DUE TO IMPROPER ASSEMBLY OF THE AIR BAG INFLATOR, WHICH IS USED IN THE SIDE AIR BAG, THE CURTAIN SHIELD AIR BAG, AND THE KNEE AIR BAG ASSEMBLY, SOME INFLATORS WERE PRODUCED WITH AN INSUFFICIENT AMOUNT OF THE HEATING AGENTS NECESSARY FOR PROPER AIR BAG DEPLOYMENT. IN THIS CONDITION, THE EXPANSION FORCE OF THE GAS MAY BE INSUFFICIENT TO PROPERLY INFLATE THE AIR BAG WHEN THE SRS SYSTEM IS ACTIVATED DURING A CRASH.
THIS MAY INCREASE THE RISK OF INJURY TO THE OCCUPANT IN THE INVOLVED SEATING POSITION IN THE EVENT OF A CRASH.
DEALERS WILL REPLACE THE SPECIFIC SRS AIR BAG. THE RECALL BEGAN ON APRIL 6, 2006. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371, SCION AT 1-866-548-1851, OR LEXUS AT 1-800-255-3987.
06V096000 · 133 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
Canadian records (Transport Canada) · 9
These are Transport Canada campaigns for 2006 Lexus GS vehicles sold in Canada. A Canadian campaign may have no US counterpart, or one under a different number covering different vehicles. For a vehicle sold in the United States, go by the NHTSA listing above and NHTSA's VIN lookup.
Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.
2021723 · 55,683 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain vehicles, the fuel delivery pipes in the engine compartment may have been produced with particles from the anti-corrosion plating on the gasket seating surface where the fuel pressure sensor is installed. This could affect the sealing properties of the gasket seated between the pressure sensor and the pipe, potentially resulting in a fuel leak. A fuel leak in the presence of an ignition source could result in a fire causing injury and/or property damage. Correction: Dealers will replace the gasket and repair the gasket seating surface.
2014458 · 18,949 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain AWD vehicles, if the floor carpet near the accelerator pedal is not reinstalled correctly following a service repair, the plastic pad embedded into the floor carpet could interfere with the operation of the accelerator pedal. If this occurs, the accelerator pedal could temporarily become stuck in a partially depressed position, rather than return to the idle position. This could result in a loss of throttle control and a crash causing property damage and/or personal injury. Correction: Dealers will modify the plastic pad.
2011080 · 852 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain GS 300, GS 300 AWD, GS 350, IS 250, IS 250 AWD and IS 350 vehicles, the fuel pressure sensor connected to the engine fuel delivery pipe may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and pipe, and through the threaded portion of the sensor. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect for fuel leakage from the threaded portion of the fuel pressure sensor. If there are no signs of a fuel leak, the fuel pressure sensor will be tightened to specifications. If a fuel leak is confirmed, the gasket between the sensor and the fuel delivery pipe will be replaced, and the sensor will be tightened.
2011037 · 11,773 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
Certain vehicles use brake fluids containing polymers that act as lubricants for certain brake system components. If during vehicle maintenance, brake fluid is used that does not contain such polymers or only small amounts, part of the internal rubber seal located at the end of the brake master cylinder piston may become dry and may curl during movement of the piston. If this occurs, a small amount of the brake fluid could slowly leak from the brake master cylinder into the brake booster, resulting in illumination of the brake warning lamp. If the brake warning light has illuminated and the vehicle continues to be operated without refilling the master cylinder brake fluid reservoir, the driver will begin to notice a spongy or soft brake pedal feel and braking performance may gradually decline. This will increase the stopping distance, increasing the likelihood of a crash. Correction: Dealers will replace the brake master cylinder seal with a newly designed one.
2010361 · 28,679 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain vehicles, the use of selected ethanol fuels may cause the aluminium fuel rails to corrode. This could result in plugged fuel injector(s), causing a rough engine idle and/or the illumination of the engine warning lamp. Corrosion may also cause a pinhole to develop on the fuel rail, which could result in fuel leakage. Fuel leakage, in the presence of an ignition source, could result in a vehicle fire. Correction: Dealers will replace the fuel rails.
2009015 · 8,391 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain GS 300, GS 300 AWD, IS 250, IS 250 AWD and IS 350 vehicles, incorrect fabrication process may cause the fuel lines to crack, possibly resulting in a leak. Fuel leakage, in the presence of an ignition source, could result in a vehicle fire causing injury or death. Correction: Dealers will replace the fuel lines.
2007377 · 1,718 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain GS 300, GS 300 AWD, GS 430, IS 250, IS 250 AWD and IS 350 vehicles, the front seat belt retractors may contain an inappropriately sized part for the emergency locking system. This can prevent the locking system from releasing when it is activated. If the seat belt is locked in this condition, the occupant may either not fasten the seat belt, or be inadequately restrained due to improper belt-fit thereby increasing the risk of injury. Correction: Dealers will replace the front seat belt assemblies.
2006078 · 1,285 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
This vehicle may contain inadequate side airbag inflators. The airbag inflators were produced with an insufficient amount of the heating agents which apply heat to the argon gas in the inflator. In this condition, expansion force of the gas in the inflator may be insufficient to properly inflate the airbag when the system is activated during a collision, which can increase the risk of injury. Correction: Dealer will replace the side airbag module.
2006068 · 1 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
2006 Lexus GS recall questions
NHTSA lists 8 recalls for the 2006 Lexus GS model year. That counts campaigns naming this model year, not recalls on your vehicle: many cover only a VIN range or production window. Transport Canada lists 9 Canadian campaigns for the Canadian-market model, shown separately.
Enter your VIN in NHTSA's recall lookup or Lexus's own, or call a Lexus dealer with your VIN. Cardog uses your VIN only to find the model year; the recalls shown here are listed for that model year and are not matched to your VIN.
Not necessarily. Transport Canada campaigns cover vehicles sold in Canada. For a vehicle sold in the United States, go by the NHTSA listing and NHTSA's VIN lookup.
Safety recall repairs are normally done at no charge by an authorized Lexus dealer. The manufacturer's notice for each campaign sets out the remedy and any conditions, so confirm with the dealer when you book.
Once Lexus's lookup or a dealer confirms a recall applies, book the repair with an authorized Lexus dealer and bring your VIN. If the manufacturer's notice says not to drive the vehicle or to park it outside, follow that instruction. Parts can take time, so book early.
Follow the manufacturer's notice for that recall. Most allow normal driving until the repair; some tell owners to stop driving or to park outside until it is fixed. Cardog does not grade recalls by severity: the manufacturer's notice and your dealer are the source.
Manufacturers must notify owners they have on record. If you bought the vehicle used or have moved, update your details with Lexus so notices reach you, and check NHTSA's lookup from time to time.
Related recall checks
Compare recall listings with alternatives to the 2006 Lexus GS.