Newest first. Many cover only part of a model year, so check your VIN with NHTSA or Ford before booking a repair.
NHTSA · listed for this model year
CERTAIN MAXZONE HEADLIGHT ASSEMBLIES, DEPO BRAND, P/NOS. 331-1129L-ASN AND 331-1129R-ASN, SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.
MAXZONE WILL NOTIFY OWNERS AND OFFER REIMBURSEMENT FOR ANY NONCOMPLIANT HEADLIGHTS. THE RECALL BEGAN ON JULY 28, 2006. OWNERS MAY CONTACT MAXZONE AT 909-822-3288.
06E067000 · 19,413 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
CERTAIN AAI MOTORSPORTS COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LIST PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."
LACK OF AMBER SIDE REFLECTORS IN THE LAMPS WILL DECREASE LIGHTING VISIBILITY TO OTHER DRIVERS AND MAY POSSIBLY RESULT IN A VEHICLE CRASH
AAI MOTORSPORTS WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 1, 2006. OWNERS MAY CONTACT AAI MOTORSPORTS AT 909-923-9188.
06E060000 · 87,745 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES EQUIPPED WITH SPEED CONTROL, THE SPEED CONTROL DEACTIVATION SWITCH MAY OVERHEAT, SMOKE, OR BURN.
A FIRE AT THE SWITCH COULD OCCUR.
BY LETTER DATED SEPTEMBER 12, 2005, OWNERS WERE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED. OWNERS WHO HAVE HAD THEIR SPEED CONTROL DEACTIVATED ARE BEING NOTIFIED THAT PARTS WILL BE AVAILABLE AND ADVISED TO MAKE AN APPOINTMENT TO RECONNECT THE SPEED CONTROL BEGINNING IN FEBRUARY 2006. OWNERS WHO DID NOT HAVE THEIR SPEED CONTROL DEACTIVATED ARE BEING NOTIFIED TO HAVE THEIR SYSTEM REMEDIED BEGINNING IN FEBRUARY 2006. OWNERS ARE URGED TO AVAIL THEMSELVES OF THE FREE DISCONNECT SERVICE AS SOON AS POSSIBLE BECAUSE OF THE SIGNIFICANT RISK OF FIRE. OWNERS MAY CONTACT FORD AT 1-800-392-3673. (NOTE: ALSO SEE RECALLS 05V017 AND 06V286)
05V388000 · 4,500,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES, IF THE INTERMEDIATE SHAFT YOKE SEPARATES FROM THE STEERING GEAR INPUT SHAFT, THE STEERING SYSTEM BECOMES DISCONNECTED.
THIS COULD RESULT IN LOSS OF STEERING CONTROL, POTENTIALLY RESULTING IN A VEHICLE CRASH WITHOUT WARNING.
DEALERS WILL INSPECT THE STEERING INTERMEDIATE SHAFT YOKE TO DETERMINE IF THE YOKE IS FULLY SEATED ON THE STEERING GEAR INPUT SHAFT. IF THE YOKE IS FULLY SEATED NO SERVICE IS REQUIRED. IF THE YOKE IS NOT FULLY SEATED AND BOLT GROOVE AND SPLINE IS VISIBLE, THE INTERMEDIATE SHAFT AND BOLT WILL BE REPLACED AS WELL AS THE BOLT AT THE STEERING COLUMN CONNECTION. OWNER NOTIFICATION BEGAN ON MAY 30, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-392-3673.
03V196000 · 171,446 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: MINI VANS, LIGHT PICKUP TRUCKS, AND SPORT UTILITY VEHICLES. OFF LEASE CANADIAN VEHICLES EQUIPPED WITH DAYTIME RUNNING LIGHTS WHICH MEET CANADIAN REQUIREMENTS AND NOT THE PHOTOMETRIC REQUIREMENTS OF FMVSS 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." ACCORDING TO FORD, THE VEHICLES WERE IMPORTED INTO THE U.S. ERRONEOUSLY.
THE LIGHT GIVEN OFF FROM THE DAYTIME RUNNING LIGHTS IS BRIGHTER THAN ALLOWED BY U.S. STANDARDS.
DEALERS WILL BE ADVISED TO DEACTIVATE THE RUNNING LIGHT FUNCTION AND TO COMPLETE ANY OUTSTANDING SAFETY RECALLS ON THESE VEHICLES.
00V168000 · 20,637 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: MULTI-PURPOSE VEHICLES. THE TRAILER HITCH ASSEMBLY TO THE FRAME ATTACHING BOLTS COULD LOSE THE CLAMP LOAD.
THE TRAILER HITCH COULD THEN SEPARATE FROM THE VEHICLE.
DEALERS WILL REPLACE THE TRAILER HITCH MOUNTING BOLTS AND NUT PLATES.
00V073000 · 565,800 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: MULTI-PURPOSE VEHICLES AND LIGHT DUTY PICKUP TRUCKS. THE LUG NUTS ON THESE VEHICLES MAY NOT CREATE SUFFICIENT CLAMP LOAD ALLOWING WHEEL MOVEMENT IN RELATION TO THE HUB/ROTOR MOUNTING SURFACE.
THIS CAN RESULT IN THE LOOSENING OF LUG NUTS, STUD FATIGUE FAILURE, AND THE POTENTIAL FOR A WHEEL SEPARATION FROM THE VEHICLE, INCREASING THE RISK OF A VEHICLE CRASH.
OWNERS OF THESE VEHICLES WILL BE RECEIVING TWO NOTIFICATIONS. THE FIRST NOTIFICATION, WHICH BEGAN IN MAY 1998, WILL PROVIDE AN INTERIM REPAIR PROCEDURE UNTIL PARTS BECOME AVAILABLE. THIS INTERIM PROCEDURE CAN BE COMPLETED BY OWNERS OR THEIR DEALERS. IT SPECIFIES THAT THE LUG NUT TORQUE MUST BE VERIFIED TO BE 100 LBS. THEN THE LUG NUTS NEED TO BE TIGHTENED AN ADDITIONAL 1/8 TO 1/4 TURN MORE. THERE WILL BE A SECOND OWNER NOTIFICATION, WHICH IS EXPECTED TO BEGIN JULY 20, 1998, UNDER WHICH DEALERS WILL INSPECT THE WHEEL STUDS AND REPLACE THE WHEEL LUG NUTS.
98V095000 · 1,520,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND MULTI-PURPOSE PASSENGER VEHICLES. IF THE AUTOMATIC TRANSMISSION SHIFT CABLE ASSEMBLY WAS NOT FULLY ATTACHED TO THE STEERING COLUMN BRACKET, THE SHIFT CABLE ASSEMBLY CAN COME OUT OF THE BRACKET. THE VEHICLE OPERATOR WOULD THEN NOT BE ABLE TO SHIFT THE TRANSMISSION FROM ONE OF THE DRIVE GEAR POSITIONS INTO THE PARK POSITION EVEN THOUGH THE GEAR SHIFT SELECTOR WOULD INDICATE "PARK."
THE CONDITION WOULD NOT ALLOW A DISENGAGEMENT OF THE TRANSMISSION FROM THE PARK POSITION OR AFFECT PROPER NEUTRAL START SWITCH OPERATION. UNINTENDED VEHICLE MOVEMENT COULD OCCUR IF THE PARKING BRAKE WAS NOT SET.
DEALERS WILL MAKE THE PROPER ATTACHMENT OF THE TRANSMISSION SHIFT CONTROL CABLE TO THE STEERING COLUMN BRACKET AND ADD A TIE STRAP TO THAT CONNECTION.
97V171000 · 866,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
THE REAR AXLE TRACK BAR BRACKET CAN SEPARATE FROM THE FRAME DUE TO MISSING WELDS OR INADEQUATE WELD PENETRATION.
IF BOTH BRACKETS SEPARATE, THE REAR AXLE CAN MOVE LATERALLY UNTIL THE TIRES CONTACT EITHER THE FRAME OR THE WHEELHOUSE RESULTING IN EITHER TIRE DAMAGE OR A SIGNIFICANT REDUCTION IN VEHICLE HANDLING PERFORMANCE.
DEALERS WILL INSTALL A TRACK BAR BRACKET REINFORCEMENT KIT AND INSPECTION OF THE AXLE TUBES. THE SUSPECT AXLE TUBES DO NOT HAVE A STAMPED DATE CODE ON THE TUBE. AXLES WITHOUT DATE CODES ON THE TUBES WILL BE REPLACED.
96V252000 · 25,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
Canadian records (Transport Canada) · 8
These are Transport Canada campaigns for 1997 Ford Expedition vehicles sold in Canada. A Canadian campaign may have no US counterpart, or one under a different number covering different vehicles. For a vehicle sold in the United States, go by the NHTSA listing above and NHTSA's VIN lookup.
On certain vehicles, the speed control deactivation switch may overheat, smoke, or burn, potentially resulting in an underhood fire. The condition may occur either when the vehicle is parked or when it is in operation. Correction: Initially as an interim repair, owners will be instructed to return their vehicles to their dealers to have the speed control deactivation switch disconnected. As soon as replacement parts are available, owners will be instructed to return to the dealers for installation of a new switch or fused wiring harness.
2005028 · 304,417 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain vehicles, Ford has issued a scheduled maintenance guide update which specifies that every 20 000 kms, the steering linkage, which includes tie-rod ends, should be inspected. The vehicle owner is asked to place the tie-rod end inspection procedure supplied with this maintenance guide update in the vehicle's glove box for reference and safekeeping. The vehicle owner is to provide the inspection procedure to their repair facility to help properly identify worn tie-rod ends. Performing the vehicle scheduled maintenance, including maintenance inspections, is the responsibility of the vehicle owner. Failure to replace worn tie-rod ends may eventually result in a tie-rod end separation that could adversely affect steering control. If the inspection reveals that a tie-rod end is worn and must be replaced, the repair will be at the owner's expense unless the vehicle is still covered by the basic vehicle warranty, or has an extended service plan coverage that includes these components.
2004164 · 305,024 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain vehicles, the intermediate steering shaft yoke may not have been properly seated onto the steering gear input shaft during installation. In this condition, the yoke may not be properly clamped to the input shaft. This may result in separation of the yoke from the steering gear input shaft and a loss of steering control, potentially resulting in a vehicle crash. Correction: Dealer will inspect the steering intermediate shaft yoke. If the yoke is not fully seated and the bolt groove and spline is visible, the intermediate shaft and bolt will be replaced as well as the bolt at the steering column connection.
2003141 · 10,942 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain vehicles, the trailer hitch assembly attachment bolts may lose clamp load. If the operator does not notice the condition due to rattle or other looseness of the trailer hitch assembly, there is a potential for the trailer hitch to separate from the vehicle. Correction: Trailer hitch mounting bolts and nut plates will be replaced with higher strength mounting bolts and nut plates installed at a higher torque and including an adhesive patch.
2000079 · 23,801 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
ON CERTAIN VEHICLES, THE LUG NUTS ON THESE VEHICLES MAY NOT CREATE SUFFICIENT CLAMP LOAD ALLOWING WHEEL MOVEMENT IN RELATION TO THE HUB/ROTOR MOUNTING SURFACE. THIS COULD RESULT IN LOOSENING OF THE LUG NUTS, STUD FATIGUE FAILURE, AND THE POTENTIAL FOR A WHEEL TO SEPARATE FROM THE VEHICLE. CORRECTION: WHEEL STUDS WILL BE INSPECTED AND WHEEL LUG NUTS WILL BE REPLACED WITH REVISED VERSIONS.
1998095 · 141,580 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
ON CERTAIN VEHICLES, THE AUTOMATIC SHIFT CABLE ASSEMBLY MAY NOT BE PROPERLY SEATED AND COULD SEPARATE FROM THE STEERING COLUMN BRACKET. SHOULD THIS OCCUR, THE OPERATOR WOULD NOT BE ABLE TO SHIFT THE TRANSMISSION FROM ONE OF THE DRIVE GEAR POSITION INTO THE PARK POSITION EVEN THOUGH THE GEAR SELECTOR WOULD INDICATE "PARK". THIS COULD RESULT IN UNINTENDED VEHICLE MOVEMENT IF THE PARKING BRAKE IS NOT SET. CORRECTION: SHIFT CONTROL CABLE WILL BE PROPERLY ATTACHED TO THE STEERING COLUMN BRACKET AND A TIE STRAP WILL BE ADDED TO THAT CONNECTION AS A REDUNDANT MEASURE TO SECURE THE ATTACHMENT.
1997180 · 72,763 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
THESE VEHICLES DO NOT COMPLY WITH C.M.V.S.S 115 - VEHICLE IDENTIFICATION NUMBER. THE FOURTH CHARACTERS OF THE V.I.N. PLATE WHICH IS AFFIXED TO THE INSTRUMENT PANEL ARE CODED "F" RATHER THAN "E". "E" IS THE APPROPRIATE CODE FOR THESE 7000 POUND GVWR VEHICLES. AS A CONSEQUENCE, THE NINTH CHARACTER (CHECK DIGIT) OF THE V.I.N. IS ALSO INCORRECT. ONLY THE V.I.N. PLATE IS IN ERROR. THE SAFETY CERTIFICATION LABELS AND OTHER DOCUMENTS ON WHICH THE VEHICLE'S V.I.N. IS LISTED DISPLAY THE CORRECT V.I.N. CORRECTION: DEALERS WILL REPLACE THE INCORRECT V.I.N. PLATES.
1997098 · 9 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
THE REAR AXLE TRACK BRACKET MAY SEPARATE FROM THE FRAME DUE TO MISSING WELDS OR A WELD PATTERN THAT IS NOT COMPATIBLE WITH THE DESIGN OF THE BRACKET. ALSO, THE REAR AXLE LOWER CONTROL ARM BRACKET MAY SEPARATE DUE TO INADEQUATE WELD PENETRATION. IF EITHER OF THESE CONDITIONS OCCURS THE VEHICLE CAN BE EASILY CONTROLLED AND BROUGHT TO A STOP. HOWEVER, IF BOTH BRACKETS WERE TO SEPARATE, THE REAR AXLE WOULD BE FREE TO MOVE LATERALLY UNTIL THE TIRES CONTACT EITHER THE FRAME OR WHEELHOUSE. THIS COULD RESULT IN EITHER TIRE DAMAGE OR A SIGNIFICANT REDUCTION IN VEHICLE HANDLING PERFORMANCE. CORRECTION: A TRACK BAR BRACKET REINFORCEMENT KIT WILL BE INSTALLED AND THE AXLE TUBES WILL BE INSPECTED AND REPLACED IF NECESSARY.
1997011 · 1,630 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
1997 Ford Expedition recall questions
NHTSA lists 9 recalls for the 1997 Ford Expedition model year. That counts campaigns naming this model year, not recalls on your vehicle: many cover only a VIN range or production window. Transport Canada lists 8 Canadian campaigns for the Canadian-market model, shown separately.
Enter your VIN in NHTSA's recall lookup or Ford's own, or call a Ford dealer with your VIN. Cardog uses your VIN only to find the model year; the recalls shown here are listed for that model year and are not matched to your VIN.
Not necessarily. Transport Canada campaigns cover vehicles sold in Canada. For a vehicle sold in the United States, go by the NHTSA listing and NHTSA's VIN lookup.
Safety recall repairs are normally done at no charge by an authorized Ford dealer. The manufacturer's notice for each campaign sets out the remedy and any conditions, so confirm with the dealer when you book.
Once Ford's lookup or a dealer confirms a recall applies, book the repair with an authorized Ford dealer and bring your VIN. If the manufacturer's notice says not to drive the vehicle or to park it outside, follow that instruction. Parts can take time, so book early.
Follow the manufacturer's notice for that recall. Most allow normal driving until the repair; some tell owners to stop driving or to park outside until it is fixed. Cardog does not grade recalls by severity: the manufacturer's notice and your dealer are the source.
Manufacturers must notify owners they have on record. If you bought the vehicle used or have moved, update your details with Ford so notices reach you, and check NHTSA's lookup from time to time.
Related recall checks
Compare recall listings with alternatives to the 1997 Ford Expedition.