Kenworth T300
Recalls listed for the Kenworth T300, newest first. Pick a year for its full record and owner complaints.
Model years
- The emergency vehicle applications that are subject of this recall are designed with a dash-mounted switch that enables the vehicle operator to inhibit the aftertreatment diesel particulate filter regeneration in envi…Transport Canada2010 Kenworth T300EmissionsSep 8, 20099 vehicles
- On certain trucks, a harness support bracket mounted on the underside of the cab may come into contact with the fuel line at the top of the fuel splitter valve (on units with a duel under-cab fuel tank setup)Transport Canada2008 Kenworth T300Fuel systemJun 4, 20082 vehicles
- The door latch may have been manufactured incorrectlyTransport Canada2008 Kenworth T300Feb 12, 20081,315 vehicles
- Certain vehicles fail to comply with requirements of CMVSS 121 - Air Brake SystemTransport Canada2008 Kenworth T300BrakesJan 7, 2008597 vehicles
- On certain trucks, the jumper wire between the grid heater relay and the fuse block may have been routed incorrectly during vehicle assemblyTransport Canada2008 Kenworth T300ElectricalMay 18, 200759 vehicles
- On certain trucks, the wiring, parts, or transmission programming required for the auto neutral feature to function as designed were either not installed, connected, or programmed properlyTransport Canada2008 Kenworth T300PowertrainApr 10, 2007349 vehicles
- On certain trucks, the axle housing may have been manufactured with steel that was out of specification (9.5mm thick instead of 11mm thick), which could result in a fatigue failure over timeTransport Canada2008 Kenworth T300Mar 20, 2007343 vehicles
- On certain trucks, the trailer light wiring harness may have been routed incorrectly during vehicle assemblyTransport Canada2008 Kenworth T300ElectricalMar 15, 200712 vehicles
- On certain trucks, an incorrect pressure sensing switch was installed in the cruise control system during vehicle assemblyTransport Canada2008 Kenworth T300EngineNov 22, 20069 vehicles
- Incorrect coating was applied to the parking brake assembly anchor bolt during fabricationTransport Canada2006 Kenworth T300BrakesSep 20, 2005121 vehicles
- The terminals on the Power Feed Harness P92-1993 were not properly crimpedTransport Canada2005 Kenworth T300ElectricalDec 10, 2004566 vehicles
- The Cummins engines were assembled using a pneumatic tool to install the boss plug, in which the air pressure was set high enough to create stresses in the cylinder block castingTransport Canada2004 Kenworth T300EngineAug 23, 20042 vehicles
- The cooling fan hub mounting bolts could fail resulting in the hub and fan assembly separating from the engine, which may result in equipment damage and/or personal injuryTransport Canada2004 Kenworth T300Aug 25, 2003451 vehicles
- The locking tab that locks the outer spindle nut onto the spindle was not engaged or properly bent overTransport Canada2003 Kenworth T300SuspensionAug 7, 200344 vehicles
- Fatigue cracks can initiate in the weld joining the bracket pin to its mounting flange on the fifth wheel assemblyTransport Canada2003 Kenworth T300May 5, 200341 vehicles
- On certain vehicles a rubber grommet from the trailer light line connector is missingTransport Canada2003 Kenworth T300LightingFeb 13, 20031,476 vehicles
- The delivery port inside Bendix trailer hand control brake valves may be partially blocked due to a problem during the molding processTransport Canada2002 Kenworth T300BrakesSep 11, 2002289 vehicles
- Certain heavy-duty trucks equipped with Meritor Wabco pneumatic antilock brake system (ABS) valve packagesTransport Canada2001 Kenworth T300Occupant protection › AirbagsJan 28, 2002223 vehicles
- Certain Kenworth vehicles manufactured between March 1996 and September 11,2001 model year T300 trucks equipped with 10,000 or 12,000 pound Dana front axlesTransport Canada2002 Kenworth T300SteeringAug 27, 2001355 vehicles
- Certain heavy duty trucks equipped with TRW tie rod ends on certain meritor axlesTransport Canada2001 Kenworth T300SteeringAug 27, 2001509 vehicles
- Certain vehicles having an intended service code of "Fire Service" and either Type 24 or larger front brake chambers or Type 36 rear brake chambers fail to comply with requirements of C.M.V.S.STransport Canada2001 Kenworth T300BrakesJun 8, 20011 vehicle
- Certain heavy duty trucks equipped with Chalmers 1000 Series and 800 Series suspension kitsTransport Canada2001 Kenworth T300May 30, 200128 vehicles
- Certain vehicles equipped with TRW brand tie rod model number 24-DLTransport Canada1999 Kenworth T300SteeringMay 17, 2001589 vehicles
- The drivelines may exceed the 35 degrees in the U-joint angleTransport Canada1999 Kenworth T300SteeringJan 11, 2000673 vehicles
- THESE VEHICLES DO NOT COMPLY WITH C.M.V.S.STransport Canada1998 Kenworth T300BrakesJul 22, 19982 vehicles