Campaigns on record across the GMC K25 (1972–1996), from Transport Canada and, tagged NHTSA, the United States. Pick a model year for the Canadian listing, and check your VIN with GMC to confirm which apply.
VEHICLE DESCRIPTION: EXTENDED-CAB PICKUP TRUCKS EQUIPPED WITH HIGH-BACK BUCKET SEATS. THE SEAT RECLINER TO FRAME ATTACHING BOLTS CAN LOOSEN, FATIGUE, AND FRACTURE ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.
IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.
DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION.
99V130000 · 59,381 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1992 gmc k25 recalls
THE FOUR U-BOLTS NUTS ON EITHER SIDE OF THE REAR AXLE WERE UNDER-TORQUED.
VEHICLE USAGE COULD CAUSE THE NUTS TO LOOSEN AND EVENTUALLY FALL OFF THE U-BOLT. THIS COULD RESULT IN SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE POTENTIAL FOR A VEHICLE CRASH.
DEALERS WILL CHECK THE U-BOLT NUT TORQUE AND RE-TORQUE ANY LOOSE U-BOLTS TO SPECIFICATION.
96V082000 · 16,918 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1996 gmc k25 recalls
THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.
IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.
DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.
95V246000 · 675,661 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1994 gmc k25 recalls
DUE TO A THIN CASE CASTING, AN EXTERNAL TRANSMISSION LEAK CAN OCCUR.
THIS CONDITION CAN CAUSE TRANSMISSION OIL TO SPRAYONTO THE EXHAUST SYSTEM AND RESULT IN A POSSIBLE VEHICLE FIRE.
DEALERS WILL INSPECT THE TRANSMISSION CASE ASSEMBLY FOR THE INVOLVED CASE CASTING. IF THE ASSEMBLY IS INVOLVED, THE TRANSMISSION WILL BE REPLACED.
95V026000 · 13,853 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1995 gmc k25 recalls
THE WINDSHIELDS WERE INSTALLED WITH INCORRECT WINDSHIELD OPENING PINCH-WELD-FLANGE PRIMER. THIS PRIMER WILL NOT PROPERLY ETCH THE PAINTED SURFACE OF THE FLANGE, ALLOWING THE WINDSHIELD TO SEPARATE FROM THE VEHICLE DURING A COLLISION. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 212, "WINDSHIELD MOUNTING."
CONSEQUENCE OF NON-COMPLIANCE: THE SEPARATION OF THE WINDSHIELD FROM THE VEHICLE DURING COLLISION INCREASES THE RISK OF INJURY FOR ALL PERSONS INVOLVED.
DEALERS WILL REMOVE THE WINDSHIELD AND REINSTALL IT USING THE CORRECT PRIMER.
94V212000 · 29 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1994 gmc k25 recalls
TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.
IF THIS OCCURS, A LOSS OF VEHICLE CONTROL AND A CRASH COULD RESULT.
DEALERS WILL TIGHTEN THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TO THE PROPER TORQUE SPECIFICATION.
94V060000 · 30,148 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1994 gmc k25 recalls
THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, "SEATING SYSTEMS."
THE MISSING BOLTS MAY CAUSE THE DRIVER'S SEAT TO BECOMELOOSE AND IN A SUDDEN STOP OR ACCIDENT MAY SUBJECT THE OCCUPANT TO INCREASEDRISK OF INJURY.
DEALERS WILL INSPECT SEATS FOR MISSING BOLTS AND INSTALL BOLTS IF REQUIRED.
93V216000 · 1,375 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1994 gmc k25 recalls
THE BRAKE PEDAL PUSH ROD RETAINER IS MISSING, MISPOSITIONED OR NOT PROPERLY SEATED.
BRAKE PEDAL PUSH ROD PROBLEMS CAN CAUSE THE STOP LAMPSWITCH AND THE BRAKE BOOSTER PUSH ROD TO DISCONNECT FROM THE BRAKE PEDAL,RESULTING IN LOSS OF BRAKE OPERATION, AND A VEHICLE CRASH COULD OCCUR WITHOUTPRIOR WARNING.
INSPECT VEHICLES TO ASSURE THE BRAKE PEDAL PUSH ROD RETAINER IS PRESENT AND FULLY SEATED IN ITS CORRECT POSITION.
93V152000 · 70,154 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1994 gmc k25 recalls
SEVERE CORROSION DUE TO ROAD SALT AT THE JOINT OF THE STAMPED STEEL CENTER SECTION AND THE CAST OUTER SECTION CAN CAUSE THE SECTIONS TO SEPARATE.
SEPARATION OF THE ROTOR SECTIONS CAN CAUSE LOSS OFBRAKING ABILITY IN THE AFFECTED WHEEL. THIS COULD RESULT IN INCREASED STOPPINGDISTANCE AND/OR LOSS OF VEHICLE CONTROL AND AN ACCIDENT.
REPLACE THE FRONT BRAKE ROTORS WITH NEW ROTORS WITH A CORROSION PROTECTION COATING. HOWEVER, IF REPLACEMENT OF BRAKE LININGS ARE NECESSARY, IT WILL BE DONE AT OWNER'S EXPENSE SINCE BRAKE LININGS ARE NORMAL MAINTENANCE ITEMS.
93V119000 · 341,364 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1992 gmc k25 recalls
LOOSE PIVOT BOLT HOLDING THE BRAKE PEDAL TO ITS SUPPORT BRACKET COULD DISENGAGE FROM THE NUT.
THIS COULD CAUSE LOSS OF BRAKING ACTIVITY THAT COULDRESULT IN A TRUCK CRASH WITHOUT PRIOR WARNING.
RETORQUE BRAKE PEDAL PIVOT BOLTS TO SPECIFICATIONS TO PREVENT LOOSENING.
90V108000 · 1,962 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1990 gmc k25 recalls
1–10 of 20