Newest first. Many cover only part of a model year, so check your VIN with Ford before booking a repair.
Transport Canada · listed for this model year
On certain vehicles, a wiring harness that is not compatible with the vehicle circuit polarity may have been inadvertently installed during servicing for recall 2005028 or 2007258. As a result, the fuse is located in the output circuit rather than in the input power feed circuit, and will not offer the intended protection in the event of an electrical short to ground. This could result in a vehicle fire, causing property damage and/or personal injury. Correction: Dealers will install an updated wiring harness.
2008038 · 8,869 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain vehicles, the speed control deactivation switch may overheat, smoke, or burn, potentially resulting in an underhood fire. The failure mode appears to be different than that of Recall 2005028 (05S28). This time, the concern is with long term durability performance issues causing the switch to fail. Correction: Initially as an interim repair, owners will be instructed to return their vehicles to their dealers to have the speed control deactivation switch disconnected. As soon as replacement parts are available, owners will be instructed to return to the dealers for installation of a fused wiring harness designed to eliminate the potential risk of fire.
2007258 · 165,447 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain natural gas vehicles, in the rare circumstance that a flame from a vehicle interior fire becomes locally directed at the natural gas tank located immediately behind the rear seat, the locally directed flame could damage the fiberglass wrap on the tank thereby reducing the hoop strength of the tank. If the hoop strength is significantly compromised, the tank could rupture and potentially result in personal injury. Correction: Dealer will install an insulator behind the seat back.
2003274 · 278 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
Certain CNG vehicles do not comply with the requirements of CMVSS 1105 - Evaporative Emissions. The natural gas fuel fill valve may leak due to flaking of the nickel plating inside the valve. This will allow natural gas to escape into the atmosphere at a rate that exceeds the limits prescribed in the standard. Correction: Valve will be replaced with one of an alternative design.
1999162 · 169 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
Note: 1996-99 crown victoria police, fleet and ngv and lincoln town car limousine equipped with a lower control arm ball joint containing a one piece bearing and 1990-96 crown victoria police, fleet and ngv and lincoln town car limousine that were serviced with either a ball joint containing an one piece bearing or a front lower control arm with a one piece bearing. High bearing loads can lead to thinning and eventual cracking of the lower control arm ball joint. This can result in separation of the ball and cap of the joint. Should this occur, the control arm to which the cap is mounted will drop to the ground. Should this occur while the vehicle is moving, reduced steering control could result in a collision. Correction: Lower control arm ball joints will be replaced.
1998251 · 4,856 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
NOTE: POLICE INTERCEPTOR VEHICLES WITH 4.6 L 2V ENGINES. UNCURED SILICONE GEL MIGRATING DOWN THE MASS AIR-FLOW SENSOR (MAFS) SENSING ELEMENT SUPPORT POSTS MAY COLLECT DUST AND DIRT PARTICLES. THESE PARTICLES CHANGE THE THERMAL CHARACTERISTICS OF THE MAFS WHICH MAY CAUSE AN ENGINE DETONATION/SPARK KNOCK CONDITION. HEAVY DETONATION CAN CAUSE SPARK PLUG DAMAGE, INTAKE VALVE OVERHEATING, VALVE SEATING CONCERNS AND PISTON/RING DAMAGE POTENTIALLY RESULTING IN ENGINE FAILURE. CORRECTION: MASS AIR-FLOW SENSORS WILL BE REPLACED.
1998144 · 1,515 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
NOTE: POLICE AND TAXI VEHICLES ONLY. THE HOOD LATCH STRIKER MAY EITHER WEAR OR BECOME DETACHED FROM THE HOOD. EITHER OF THESE CONDITIONS MAY RESULT IN THE HOOD OPENING WITHOUT WARNING WHILE THE VEHICLE IS BEING OPERATED RESULTING IN REDUCED DRIVER VISIBILITY AND A POSSIBLE CRASH. CORRECTION: VEHICLES WITH 1992 MODEL HOODS WILL HAVE AN IMPROVED HOOD LATCH STRIKER INSTALLED AND REVISED STRIKER PLATE ATTACHING FASTENERS WILL BE INSTALLED ON VEHICLES WITH 1993-97 HOODS.
1997069 · 5,986 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
NOTE: CROWN VICTORIA POLICE INTERCEPTORS AND UNITS FOR COMMERCIAL APPLICATIONS. TOWN CARS WITH LIMOUSINE BUILDER PACKAGE OR TRAILER TOW PACKAGE. THE PITMAN ARMS ON THESE VEHICLES WERE NOT FULLY LUBRICATED DURING VEHICLE ASSEMBLY. IF NOT PROPERLY LUBRICATED IN ACCORDANCE WITH THE MAINTENANCE SCHEDULE, THE PITMAN ARM BALL JOINT MAY BECOME CONTAMINATED AND CORRODE. THIS COULD RESULT IN ABNORMAL WEAR AND POSSIBLE PITMAN ARM BALL JOINT SEPARATION CAUSING SUBSEQUENT LOSS OF STEERING CONTROL AND A POSSIBLE CRASH. CORRECTION: PITMAN ARMS WILL BE INSPECTED AND THOSE WITH SIGNIFICANT WEAR WILL BE REPLACED. THOSE PITMAN ARMS NOT REPLACED WILL HAVE THE BALL JOINT FULLY GREASED.
1996121 · 2,786 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
THESE VEHICLES MAY NOT COMPLY WITH C.M.V.S.S 206 - DOOR LATCHES, HINGES AND LOCKS. THE DRIVER'S DOOR, WHEN CLOSED ONLY TO THE SECONDARY LATCHED POSITION, MAY NOT SUSTAIN A 1000 POUND TRANSVERSE LOAD AS REQUIRED BY THE STANDARD. CORRECTION: DRIVER DOOR LATCH WILL BE INSPECTED AND, IF NECESSARY, REPLACED.
1996071 · 3,296 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
United States records (NHTSA) · 12
These are NHTSA campaigns for 1996 Ford Crown Victoria vehicles sold in the United States. They are not Canadian recalls: NHTSA's VIN lookup has no Canadian data, and a US campaign may have no Canadian counterpart, or one under a different number covering different vehicles. For a vehicle sold in Canada, go by the Transport Canada listing above and Ford's Canadian VIN lookup.
Dorman Products, Inc. (Dorman) is recalling certain model Dorman Steering Shafts, part number 425-359, Solutions Steering Shafts, part number 7-0359, and OE Solutions Steering Shafts, part number 425-359, manufactured April 17, 2014, to September 28, 2015. These aftermarket replacement steering shafts are sold for use in 1995-2002 Ford Crown Victoria, Mercury Grand Marquis, and Lincoln Town Car vehicles. These steering shafts may separate during operation if the integral fastener is loose or missing and if the interfacing vehicle shaft is compressed in length.
If the shafts separate during vehicle operation, a loss of steering control would result, increasing the risk of a vehicle crash.
Dorman will notify owners, and dealers will replace the steering shaft, free of charge. The recall began on October 28, 2015. Owners may contact Dorman customer service at 1-800-523-2492, option 5.
15E082000 · 1,767 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
FORD IS RECALLING 225,000 MY 1992-2003 ECONOLINE, MY 1993-1995 TAURUS SHO, MY 1992-1998 CROWN VICTORIA, MY 1993 BRONCO, F-SERIES, MY 1995-1997 F-SERIES SUPER DUTY STRIPPED CHASSIS, MY 1992-1998 MERCURY GRAND MARQUIS, AND MY 1992-1995 LINCOLN TOWN CAR VEHICLES. THE AFFECTED VEHICLES WERE PREVIOUSLY REPAIRED USING A WIRING HARNESS THAT IS NOT COMPATIBLE WITH THE VEHICLE CIRCUIT POLARITY.
AS A RESULT, THE FUSE IS LOCATED IN THE OUTPUT CIRCUIT RATHER THAN IN THE INTENDED INPUT POWER FEED CIRCUIT, AND MAY NOT OFFER THE INTENDED PROTECTION IN THE EVENT OF AN ELECTRICAL SHORT TO GROUND.
DEALERS WILL INSTALL A NEW WIRING HARNESS, OR REPLACE THE MATING ELECTRICAL COMPONENT. THE RECALL BEGAN ON FEBRUARY 18, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
08V051000 · 225,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.
THIS COULD RESULT IN AN UNDERHOOD FIRE.
DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.
07V336000 · 3,600,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
ON CERTAIN NATURAL GAS VEHICLES, IF A FLAME FROM A VEHICLE INTERIOR FIRE BECOMES LOCALLY DIRECTED AT THE NATURAL GAS FUEL TANK LOCATED IMMEDIATELY BEHIND THE REAR SEAT, THE FLAME COULD DAMAGE THE FIBERGLASS WRAP ON THE TANK WEAKENING THE TANK.
IF THE STRENGTH OF THE TANK IS SIGNIFICANTLY COMPROMISED, IT COULD RUPTURE, INCREASING THE RISK OF A FIRE.
DEALERS WILL INSTALL AN INSULATOR BEHIND THE CURRENT SEAT BACK. OWNER NOTIFICATION BEGAN ON JANUARY 7, 2004. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.
03V472000 · 4,218 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
IN ORDER TO ENHANCE POLICE OFFICE SAFETY, MODEL YEAR 1992-2003 CROWN VICTORIA POLICE INTERCEPTOR (CVPI) VEHICLES WILL BE EQUIPPED WITH SHIELDS DESIGNED TO HELP PROTECT THE FUEL TANK IN HIGH-SPEED REAR-IMPACT CRASHES. FORD ALSO WILL BE OFFERING AN OPTIONAL TRUNK PACKAGE DESIGNED TO IMPROVE THE SAFE TRANSPORT OF SHARP-EDGED, HEAVY EQUIPMENT IN THESE VEHICLES.
SOME HIGH-SPEED REAR-IMPACT CRASHES HAVE RESULTED IN FUEL TANK PUNCTURES AND FIRES IN CVPI VEHICLES.
FORD HAS ADVISED US THAT SHIELD KITS HAVE BEEN AVAILABLE SINCE LATE OCTOBER AND WILL BE INSTALLED ON POLICE INTERCEPTOR VEHICLES AT NO COST. THE OPTIONAL TRANK PACKAGE WILL BE AVAILABLE BY THE END OF 2002. FORD HAS ESTABLISHED A NEW WEB SITE AT WWW.CVPI.COM TO ANSWER ADDITIONAL QUESTIONS ABOUT THE SAFE USE OF CPVI VEHICLES.
02I003000 · 350,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET FRONT PASSENGER SIDE SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.
IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.
DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.
00V157002 · 1,129 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET DRIVER'S SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.
IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.
DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.
00V157001 · 1,167 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.
IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.
DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).
98V322000 · 175,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH FEDERAL REGULATION 573. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. FORD IS INITIATING AN OWNER NOTIFICATION PROGRAM FOR OWNERS OF CERTAIN 1995-1997 CROWN VICTORIA MODEL VEHICLES WITH POLICE, TAXI, AND COMMERCIAL FLEET PACKAGES AND TOWN CAR VEHICLES WITH THE LIVERY PACKAGE. THESE VEHICLES MAY HAVE INSUFFICIENT CLEARANCE BETWEEN THE BRAKE LINE AND THE UNDERBODY FRONT FLOOR PAN ASSEMBLY WHICH COULD CAUSE WEAR OF THE BRAKE LINES.
THIS COULD LEAD TO BRAKE FLUID LOSS FOR THE REAR BRAKES AND, POTENTIALLY, INCREASED STOPPING DISTANCES.
DEALERS WILL INSPECT THE BRAKE LINES FOR WEAR, INSTALL TWO NEW TUBE BUNDLE CLIPS, AND CHECK THE BRAKE LINES FOR PROPER CLEARANCES. IF THE BRAKE LINES ARE WORN, THE DAMAGED SECTION OF THE BRAKE LINE WILL BE REPLACED.
98I001000 · 167,742 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: POLICE AND TAXI VEHICLES. THE HOOD LATCH STRIKER CAN WEAR OR BECOME DETACHED FROM THE HOOD.
EITHER OF THESE CONDITIONS CAN RESULT IN THE HOOD OPENING WITHOUT WARNING WHILE THE VEHICLE IS BEING OPERATED IMPAIRING THE DRIVER'S VISIBILITY.
DEALERS WILL INSTALL AN IMPROVED HOOD LATCH STRIKER (VEHICLES WITH 1992 MODEL HOODS) OR REVISED STRIKER PLATE ATTACHING FASTENERS (VEHICLES WITH 1993-1997 MODEL HOODS).
97V024000 · 125,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
THE PITMAN ARMS WERE NOT FULLY LUBRICATED AT THE ASSEMBLY PLANT. THE "BALL JOINT" AT THE OUTER END OF THE PITMAN ARM CAN BECOME CONTAMINATED AND CORRODE.
SUCH CORROSION CAN RESULT IN ABNORMAL WEAR OF THE JOINT, RESULTING IN SEPARATION OF THE JOINT. LOSS OF STEERING CONTROL CAN OCCUR INCREASING THE RISK OF A VEHICLE ACCIDENT.
DEALERS WILL INSPECT THE VEHICLES AND IF THE JOINT IS FOUND TO HAVE SIGNIFICANT WEAR, THE ARM WILL BE REPLACED. THOSE PITMAN ARMS NOT REPLACED WILL HAVE THE "BALL JOINT" FULLY GREASED.
96V135000 · 72,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
WHEN IN THE SECONDARY LATCHED POSITION, THE DRIVER DOOR LATCHES MAY OPEN WHEN SUBJECTED TO TRANSVERSE LOADS LESS THAN THAT SPECIFIED IN FMVSS NO. 206, "DOOR LOCKS AND DOOR RETENTION COMPONENTS."
THE DRIVER'S DOOR, WHEN CLOSED ONLY TO THE SECONDARY LATCHED POSITION, MAY NOT SUSTAIN A 1,000 POUND TRANSVERSE LOAD.
DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE DRIVER DOOR LATCH.
96V070000 · 73,500 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
1996 Ford Crown Victoria recall questions
Transport Canada lists 9 recalls for the 1996 Ford Crown Victoria model year. That counts campaigns naming this model year, not recalls on your vehicle: many cover only a VIN range or production window, and some only vehicles found on inspection. NHTSA lists 12 United States campaigns for the US-market model, shown separately; a US campaign may have no Canadian equivalent.
Enter your VIN in Ford's Canadian recall lookup, or call a Ford dealer with your VIN. In Canada the manufacturer is responsible for showing recall and repair status for each VIN, so its lookup is the authoritative answer. Cardog uses your VIN only to find the model year; the recalls shown here are listed for that model year and are not matched to your VIN.
Not necessarily. NHTSA campaigns cover vehicles sold in the United States, and NHTSA's VIN lookup has no Canadian data. When a defect also affects Canadian vehicles, the manufacturer files a separate notice with Transport Canada, often under a different number and sometimes covering a different set of vehicles. For a Canadian vehicle, go by the Transport Canada listing and Ford's Canadian lookup.
Safety recall repairs are normally done at no charge by an authorized Ford dealer. The manufacturer's notice for each campaign sets out the remedy and any conditions, so confirm with the dealer when you book.
Once Ford's lookup or a dealer confirms a recall applies, book the repair with an authorized Ford dealer and bring your VIN. If the manufacturer's notice says not to drive the vehicle or to park it outside, follow that instruction. Parts can take time, so book early.
Follow the manufacturer's notice for that recall. Most allow normal driving until the repair; some tell owners to stop driving or to park outside until it is fixed. Cardog does not grade recalls by severity: the manufacturer's notice and your dealer are the source.
Manufacturers must notify owners they have on record. If you bought the vehicle used or have moved, update your details with Ford Canada so notices reach you, and check the manufacturer's lookup from time to time.
Related recall checks
Compare recall listings with alternatives to the 1996 Ford Crown Victoria.