Newest first. Many cover only part of a model year, so check your VIN with Dodge before booking a repair.
Transport Canada · listed for this model year
On certain vehicles equipped with an automatic transmission and a floor-mounted shifter, the ignition-park interlock may become defeated and allow the shifter to be moved out of the Park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the Park position. This may result in the vehicle rolling away without warning. Correction: Dealer will inspect the function of the ignition-park interlock system. Vehicles found with functional interlock systems will have a load-limiting push rod installed into the floor shifter lever. Vehicles with a non-functional ignition-park interlock system will have the shifter assembly replaced.
2004003 · 277,416 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
Certain vehicles may not comply with CMVSS 1103 - exhaust emissions. During calibration, the purge flow monitor may have been inadvertently disabled in the area of purge flow detection. Correction: Powertrain Control Module will be reflashed with proper calibrations.
1998227 · 47 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
NOTE: VEHICLES EQUIPPED WITH A FLOOR MOUNTED AUTOMATIC TRANSMISSION SHIFT LEVER. A COMBINATION OF APPLYING A MIS-ADJUSTED SHIFTER RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION MAY BREAK THE CONNECTING PIN IN THE SHIFTER. IF THIS HAPPENS, THE "IGNITION-PARK" INTERLOCK SYSTEM WILL NOT FUNCTION. CORRECTION: THE CONSOLE SHIFT INTERLOCK MECHANISM WILL BE INSPECTED FOR PROPER FUNCTION. ANY VEHICLES THAT ARE NOT FUNCTIONAL AFTER THE INSPECTION WILL HAVE THE SHIFT MECHANISM AND CABLE REPLACED WITH A CURRENT PRODUCTION "SELF ADJUSTING" DESIGN.
1998165 · 61,866 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
Certain vehicles do not comply with CMVSS 1103 - exhaust emissions. The calibration of the Powertrain Control Module (PCM) may fail to adequately control CO emissions. Correction: PCM will be reflashed with a new calibration.
1998010 · 12,494 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain vehicles, the lower control arm ball joint may separate due to loss of lubrication. This separation could result in loss of vehicle control and a crash without prior warning. Correction: Ball joint end housing cover seal will be inspected for leakage and the rubber boot will be inspected for damage. If the cover seal leaks or the boot is damaged, the lower control arm will be replaced.
1997205 · 53,134 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
THE PRIMARY/SECONDARY HOOD LATCH SPRING MAY NOT REMAIN IN POSITION DURING HOOD CLOSING, WHICH CAN RESULT IN LOSS OF BOTH THE PRIMARY AND SECONDARY LATCH FUNCTION. LOSS OF HOOD FUNCTION CAN RESULT IN A HOOD FLY-UP CONDITION. CORRECTION: THE SECONDARY HOOD LATCH SPRING WILL BE REPLACED WITH ONE HAVING A LONGER END HOOK.
1997123 · 21,272 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain vehicles, the brake master cylinder may leak brake fluid due to a damaged double lip rear piston seal. Brake fluid leakage may result in diminished effectiveness of one portion of the split brake system. Correction: Rear brake master cylinder piston assemblies will be replaced.
1996079 · 6,257 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
CORROSION OF THE ABS HYDRAULIC CONTROL UNIT MAY CAUSE THE SOLENOID VALVES TO STICK IN THE OPEN POSITION. IF EITHER FRONT WHEEL VALVE STICKS, THE VEHICLE MAY TEND TO DEVIATE FROM A STRAIGHT STOP WHEN THE BRAKES ARE APPLIED. CORRECTION: A PLATE WILL BE INSTALLED ON THE ABS HYDRAULIC CONTROL UNIT AND SILICONE GREASE INJECTED INTO THE SOLENOID CAVITY TO ELIMINATE THE POTENTIAL FOR THIS CONDITION.
1996078 · 9,358 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
AN ENGINE CYLINDER HEAD OIL GALLEY PLUG MAY NOT BE ADEQUATELY RETAINED. INADEQUATE RETENTION OF THE PLUG MAY RESULT IN OIL LEAKAGE WHICH COULD POTENTIALLY CAUSE A FIRE IN THE ENGINE COMPARTMENT. CORRECTION: AN EXPANSION PLUG AND RETAINING BRACKET WILL BE INSTALLED OVER THE SUSPECT CYLINDER HEAD OIL GALLEY PLUG.
1996009 · 5,733 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
United States records (NHTSA) · 11
These are NHTSA campaigns for 1996 Dodge Stratus vehicles sold in the United States. They are not Canadian recalls: NHTSA's VIN lookup has no Canadian data, and a US campaign may have no Canadian counterpart, or one under a different number covering different vehicles. For a vehicle sold in Canada, go by the Transport Canada listing above and Dodge's Canadian VIN lookup.
FEDERAL-MOGUL IS RECALLING CERTAIN REPLACEMENT CONTROL ARM ASSEMBLIES, PART NUMBERS K7425, 10945, FA4510X, K7427, 10946, AND FA4611X, SOLD FOR USE ON VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE BALL JOINT ON THE CONTROL ARM ASSEMBLY CAN FAIL CAUSING THE BALL STUD TO WEAR THROUGH THE CONTROL ARM HOUSING RESULTING IN NOISE AND/OR SEPARATION OF THE BALL STUD FROM THE HOUSING.
IF THERE IS A SEPARATION OF THE BALL STUD FROM THE HOUSING, THE DRIVER CAN LOOSE STEERING CONTROL, POSSIBLY RESULTING IN A VEHICLE CRASH.
FEDERAL-MOGUL WILL NOTIFY OWNERS OF RECORD AND REPLACE THE AFFECTED CONTROL ARMS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 28, 2011. OWNERS MAY CONTACT FEDERAL-MOGUL AT 1-877-489-6659.
10E059000 · 22,689 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
QUALIS AUTOMOTIVE IS RECALLING CERTAIN AFTERMARKET BALL JOINTS SOLD FOR USE ON CERTAIN PASSENGER VEHICLES. THE SOCKET MAY HAVE BEEN EXCESSIVELY HARDENED WHICH COULD CAUSE IT TO CRACK NEAR THE RETAINING RING GROOVE ALLOWING THE BALL STUD TO SEPARATE UNDER IMPACT LOAD. THE SUBJECT BALL JOINTS WERE SOLD AS FOUR PART NUMBERS, D10945, D10946, G10945, AND G10946. THE AFFECTED CONTROL ARMS, D10945 AND D10946, ARE STAMPED WITH THE FOLLOWING DATES ON THE BALL JOINTS: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, AND 116609. THE G10945 AND G10946 ARE THE SAME PART AS THE D10945 AND D10946 RESPECTIVELY. THEY ARE LABELED DIFFERENTLY DEPENDING ON THE AFTERMARKET CUSTOMER.
SEPARATION OF THE BALL STUD FROM THE SOCKET OF THE BALL JOINT HOUSING WOULD ALLOW THE CONTROL ARM TO COLLAPSE AND THE WHEEL TO FOLD IN CAUSING LOSS OF STEERING CONTROL, POSSIBLY RESULTING IN A CRASH.
QUALIS AUTOMOTIVE WILL REPLACE THE BALL JOINTS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 9, 2009. OWNERS MAY CONTACT QUALIS AUTOMOTIVE AT 1-800-493-4128.
09E056000 · 5,787 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
CERTAIN AIRTEX FUEL PUMP MODULES, P/NOS. E7089M, E7094M, E7113M, AND E7129M, MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006. THESE FUEL PUMP MODULES WERE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.
FUEL RESTRICTION COULD RESULT IN LOSS OF POWER AND/OR ENGINE STALL, POSSIBLY RESULTING IN A VEHICLE CRASH.
AIRTEX WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT AIRTEX TOLL-FREE AT 1-866-867-3759.
06E091000 · 24,358 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
CERTAIN TIGAS FUEL PUMP MODULES MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006, SOLD UNDER VARIOUS BRAND NAMES AND P/NOS. THESE FUEL PUMP MODULES ARE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.
FUEL RESTRICTION COULD RESULT IN LOSS OF POWER AND/OR ENGINE STALL, POSSIBLY RESULTING IN A VEHICLE CRASH.
TI AUTOMOTIVE WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 6, 2006. OWNERS MAY CONTACT TI AUTOMOTIVE TOLL-FREE AT 1-877-461-1834.
06E088000 · 39,243 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
ON CERTAIN PASSENGER VEHICLES, THE FLOOR SHIFTER IGNITION-PARK INTERLOCK MAY FAIL AND ALLOW THE SHIFTER TO BE MOVED OUT OF THE PARK POSITION WITH THE KEY REMOVED. AN INOPERATIVE INTERLOCK MAY ALSO ALLOW THE KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE PARK POSITION.
EITHER CIRCUMSTANCE MAY RESULT IN THE VEHICLE ROLLING AWAY WITHOUT WARNING.
DEALERS WILL INSTALL A NEW LOAD-LIMITING PUSH ROD INTO THE FLOOR SHIFTER LEVER OF THE AFFECTED VEHICLES. OWNER NOTIFICATION BEGAN ON JUNE 14, 2004. OWNERS SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
04V021000 · 2,315,768 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE ADJUSTMENT OF THE CABLE CONNECTING THE CONSOLE SHIFTER MECHANISM TO THE IGNITION KEY CAN CAUSE A TRAPPED KEY CONDITION WHICH CAN RESULT IN A LOW FORCE REQUIRED TO DEPRESS THE SHIFT BUTTON. A COMBINATION OF APPLYING A MIS-ADJUSTED RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION, CAN BREAK THE CONNECTING PIN IN THE SHIFTER.
IF THIS HAPPENS, THE "IGNITION-PARK" INTERLOCK SYSTEM WILL BE NONFUNCTIONAL.
DEALERS WILL INSPECT FOR PROPER OPERATION OF THE SYSTEM. ANY VEHICLES THAT ARE NOT FUNCTIONAL AFTER THE INSPECTION WILL HAVE THE SHIFT MECHANISM AND CABLE REPLACED WITH A "SELF-ADJUSTING" DESIGN.
98V183000 · 685,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER CONTROL ARM BALL JOINT CAN SEPARATE DUE TO LOSS OF LUBRICATION.
SEPARATION OF THE BALL JOINT COULD CAUSE A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE CRASH.
DEALERS WILL INSPECT THE BALL JOINT END HOUSING COVER SEAL FOR LEAKAGE WITH A HIGH PRESSURE AIR TESTER AND THE RUBBER BOOT WILL BE VISUALLY INSPECTED FOR DAMAGE. IF THE COVER SEAL LEAKS OR THE BOOT IS DAMAGED, THE LOWER CONTROL ARM WILL BE REPLACED.
97V201000 · 599,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SECONDARY HOOD LATCH SPRING CAN DISENGAGE FROM ITS RETENTION HOLE IF THE HOOD IS SLAMMED SHUT.
IF THIS CONDITION OCCURS SIMULTANEOUSLY WITHOUT ENGAGING THE PRIMARY LATCH, THE HOOD WOULD NOT BE RESTRAINED INCREASING THE RISK OF A VEHICLE CRASH.
DEALERS WILL REPLACE THE SECONDARY HOOD LATCH SPRING WITH A LONGER END HOOK SPRING.
97V095000 · 219,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
THE BRAKE MASTER CYLINDER CAN LEAK BRAKE FLUID DUE TO A DAMAGED DOUBLE LIP REAR PISTON SEAL.
BRAKE FLUID LEAKAGE CAN RESULT IN DIMINISHED EFFECTIVENESS OF ONE HALF OF THE SPLIT BRAKE SYSTEM. THE INSTRUMENT PANEL WARNING LIGHT(S) WILL SIGNAL SYSTEM IMPAIRMENT PRIOR TO PARTIAL BRAKE SYSTEM LOSS.
DEALERS WILL REPLACE THE REAR BRAKE MASTER CYLINDR PISTON ASSEMBLY.
96V075000 · 151,800 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
CORROSION OF THE ABS HYDRAULIC CONTROL UNIT CAN CAUSE THE SOLENOID VALVES TO STICK IN THE OPEN POSITION.
IF EITHER FRONT WHEEL VALVE STICKS, THE VEHICLE WOULD SWERVE FROM A STRAIGHT STOP WHEN THE BRAKES ARE APPLIED.
DEALERS WILL INSTALL A PLATE AND SILICONE GREASE INJECTED INTO THE SOLENOID CAVITY TO ELIMINATE THE POTENTIAL FOR THIS CONDITION.
96V074000 · 90,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
IN CERTAIN VEHICLES, THE ENGINE CYLINDER HEAD OIL GALLEY PLUG DOES NOT SEAL PROPERLY AND ENGINE CYLINDER HEAD OIL IS NOT ADEQUATELY RETAINED.
INADEQUATE SEALING AND RETENTION OF THE PLUG CAN RESULT IN OIL LEAKAGE WHICH COULD CAUSE A FIRE IN THE ENGINE COMPARTMENT.
DEALERS WILL INSTALL AN EXPANSION PLUG AND RETAINING BRACKET OVER THE CYLINDER HEAD OIL GALLEY PLUG.
96V006000 · 40,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
1996 Dodge Stratus recall questions
Transport Canada lists 9 recalls for the 1996 Dodge Stratus model year. That counts campaigns naming this model year, not recalls on your vehicle: many cover only a VIN range or production window, and some only vehicles found on inspection. NHTSA lists 11 United States campaigns for the US-market model, shown separately; a US campaign may have no Canadian equivalent.
Enter your VIN in Dodge's Canadian recall lookup, or call a Dodge dealer with your VIN. In Canada the manufacturer is responsible for showing recall and repair status for each VIN, so its lookup is the authoritative answer. Cardog uses your VIN only to find the model year; the recalls shown here are listed for that model year and are not matched to your VIN.
Not necessarily. NHTSA campaigns cover vehicles sold in the United States, and NHTSA's VIN lookup has no Canadian data. When a defect also affects Canadian vehicles, the manufacturer files a separate notice with Transport Canada, often under a different number and sometimes covering a different set of vehicles. For a Canadian vehicle, go by the Transport Canada listing and Dodge's Canadian lookup.
Safety recall repairs are normally done at no charge by an authorized Dodge dealer. The manufacturer's notice for each campaign sets out the remedy and any conditions, so confirm with the dealer when you book.
Once Dodge's lookup or a dealer confirms a recall applies, book the repair with an authorized Dodge dealer and bring your VIN. If the manufacturer's notice says not to drive the vehicle or to park it outside, follow that instruction. Parts can take time, so book early.
Follow the manufacturer's notice for that recall. Most allow normal driving until the repair; some tell owners to stop driving or to park outside until it is fixed. Cardog does not grade recalls by severity: the manufacturer's notice and your dealer are the source.
Manufacturers must notify owners they have on record. If you bought the vehicle used or have moved, update your details with Dodge Canada so notices reach you, and check the manufacturer's lookup from time to time.
Related recall checks
Compare recall listings with alternatives to the 1996 Dodge Stratus.