Newest first. Many cover only part of a model year, so check your VIN with Chrysler before booking a repair.
Transport Canada · listed for this model year
On certain vehicles equipped with an automatic transmission and a floor-mounted shifter, the ignition-park interlock may become defeated and allow the shifter to be moved out of the Park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the Park position. This may result in the vehicle rolling away without warning. Correction: Dealer will inspect the function of the ignition-park interlock system. Vehicles found with functional interlock systems will have a load-limiting push rod installed into the floor shifter lever. Vehicles with a non-functional ignition-park interlock system will have the shifter assembly replaced.
2004003 · 277,416 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
On certain vehicles, the lower lateral arm ball joint can separate due to loss of lubrication. There is a potential for moisture to leak past the protective boot which can cause the ball stud to corrode. This corrosion, acting much like contamination, can also lead to premature wear and separation of the ball joint. This could result in loss of vehicle control and a possible crash. Correction: Lower lateral arm ball joints will be inspected for wear and replaced as necessary with newly designed lower lateral arm ball joints. Ball joints that are within the established tolerance will be cleaned and a special sealant will be applied to prevent the intrusion of moisture.
2001062 · 18,687 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
NOTE: VEHICLES EQUIPPED WITH A FLOOR MOUNTED AUTOMATIC TRANSMISSION SHIFT LEVER. A COMBINATION OF APPLYING A MIS-ADJUSTED SHIFTER RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION MAY BREAK THE CONNECTING PIN IN THE SHIFTER. IF THIS HAPPENS, THE "IGNITION-PARK" INTERLOCK SYSTEM WILL NOT FUNCTION. CORRECTION: THE CONSOLE SHIFT INTERLOCK MECHANISM WILL BE INSPECTED FOR PROPER FUNCTION. ANY VEHICLES THAT ARE NOT FUNCTIONAL AFTER THE INSPECTION WILL HAVE THE SHIFT MECHANISM AND CABLE REPLACED WITH A CURRENT PRODUCTION "SELF ADJUSTING" DESIGN.
1998165 · 61,866 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
THE DASH PANEL MAY SAG AND INTERFERE WITH THE ACCELERATOR PEDAL WHICH COULD PREVENT THE THROTTLE FROM CLOSING OR RESULT IN A THROTTLE STICKING CONDITION. CORRECTION: THE DASH PANEL PAD WILL BE TRIMMED ABOVE THE ACCELERATOR PEDAL.
1998090 · 1,010 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
Certain sebring convertible vehicles do not comply with CMVSS. 1101 - emission device. The vehicle emission control information (veci) label has an error in the hose routing schematic. Correction: Correct labels and installation instructions will be mailed to owners.
1997220 · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
United States records (NHTSA) · 13
These are NHTSA campaigns for 1998 Chrysler Sebring vehicles sold in the United States. They are not Canadian recalls: NHTSA's VIN lookup has no Canadian data, and a US campaign may have no Canadian counterpart, or one under a different number covering different vehicles. For a vehicle sold in Canada, go by the Transport Canada listing above and Chrysler's Canadian VIN lookup.
FEDERAL-MOGUL IS RECALLING CERTAIN REPLACEMENT CONTROL ARM ASSEMBLIES, PART NUMBERS K7425, 10945, FA4510X, K7427, 10946, AND FA4611X, SOLD FOR USE ON VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE BALL JOINT ON THE CONTROL ARM ASSEMBLY CAN FAIL CAUSING THE BALL STUD TO WEAR THROUGH THE CONTROL ARM HOUSING RESULTING IN NOISE AND/OR SEPARATION OF THE BALL STUD FROM THE HOUSING.
IF THERE IS A SEPARATION OF THE BALL STUD FROM THE HOUSING, THE DRIVER CAN LOOSE STEERING CONTROL, POSSIBLY RESULTING IN A VEHICLE CRASH.
FEDERAL-MOGUL WILL NOTIFY OWNERS OF RECORD AND REPLACE THE AFFECTED CONTROL ARMS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 28, 2011. OWNERS MAY CONTACT FEDERAL-MOGUL AT 1-877-489-6659.
10E059000 · 22,689 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
QUALIS AUTOMOTIVE IS RECALLING CERTAIN AFTERMARKET BALL JOINTS SOLD FOR USE ON CERTAIN PASSENGER VEHICLES. THE SOCKET MAY HAVE BEEN EXCESSIVELY HARDENED WHICH COULD CAUSE IT TO CRACK NEAR THE RETAINING RING GROOVE ALLOWING THE BALL STUD TO SEPARATE UNDER IMPACT LOAD. THE SUBJECT BALL JOINTS WERE SOLD AS FOUR PART NUMBERS, D10945, D10946, G10945, AND G10946. THE AFFECTED CONTROL ARMS, D10945 AND D10946, ARE STAMPED WITH THE FOLLOWING DATES ON THE BALL JOINTS: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, AND 116609. THE G10945 AND G10946 ARE THE SAME PART AS THE D10945 AND D10946 RESPECTIVELY. THEY ARE LABELED DIFFERENTLY DEPENDING ON THE AFTERMARKET CUSTOMER.
SEPARATION OF THE BALL STUD FROM THE SOCKET OF THE BALL JOINT HOUSING WOULD ALLOW THE CONTROL ARM TO COLLAPSE AND THE WHEEL TO FOLD IN CAUSING LOSS OF STEERING CONTROL, POSSIBLY RESULTING IN A CRASH.
QUALIS AUTOMOTIVE WILL REPLACE THE BALL JOINTS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 9, 2009. OWNERS MAY CONTACT QUALIS AUTOMOTIVE AT 1-800-493-4128.
09E056000 · 5,787 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.
DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.
SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.
09E012000 · 16,270 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
CERTAIN AIRTEX FUEL PUMP MODULE ASSEMBLIES, P/N E7081H, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE VEHICLES LISTED ABOVE. THE WALL OF THE FLARED FITTING OF THE FUEL PUMP IS NOT THICK ENOUGH TO PREVENT THE MATING THREADED FITTINGS FROM BOTTOMING OUT BEFORE AN ADEQUATE SEAL IS ACHIEVED. THIS CONDITION MAY RESULT IN LEAKAGE OF FUEL AT THE CONNECTION OF THE VEHICLE FUEL LINE AND THE FUEL PUMP MODULE ASSEMBLY.
IN THE PRESENCE OF AN IGNITION SOURCE, A FUEL LEAK COULD RESULT IN A FIRE.
AIRTEX WILL NOTIFY OWNERS AND REPLACE THE FUEL PUMPS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING JULY 2007. OWNERS CAN CONTACT AIRTEX AUTOMOTIVE AT 800-880-3056.
07E055000 · 222 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
CERTAIN AIRTEX FUEL PUMP MODULES, P/NOS. E7089M, E7094M, E7113M, AND E7129M, MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006. THESE FUEL PUMP MODULES WERE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.
FUEL RESTRICTION COULD RESULT IN LOSS OF POWER AND/OR ENGINE STALL, POSSIBLY RESULTING IN A VEHICLE CRASH.
AIRTEX WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT AIRTEX TOLL-FREE AT 1-866-867-3759.
06E091000 · 24,358 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
CERTAIN TIGAS FUEL PUMP MODULES MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006, SOLD UNDER VARIOUS BRAND NAMES AND P/NOS. THESE FUEL PUMP MODULES ARE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.
FUEL RESTRICTION COULD RESULT IN LOSS OF POWER AND/OR ENGINE STALL, POSSIBLY RESULTING IN A VEHICLE CRASH.
TI AUTOMOTIVE WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 6, 2006. OWNERS MAY CONTACT TI AUTOMOTIVE TOLL-FREE AT 1-877-461-1834.
06E088000 · 39,243 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
CERTAIN TRADESONIC COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
LACK OF AMBER SIDE REFLECTORS IN THE LAMPS WILL DECREASE LIGHTING VISIBILITY TO OTHER DRIVERS AND MAY POSSIBLY RESULT IN A VEHICLE CRASH.
TRADESONIC WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING JULY 2006. OWNERS MAY CONTACT TRADESONIC AT 626-934-8884.
06E064000 · 4,029 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
ON CERTAIN PASSENGER VEHICLES, THE FLOOR SHIFTER IGNITION-PARK INTERLOCK MAY FAIL AND ALLOW THE SHIFTER TO BE MOVED OUT OF THE PARK POSITION WITH THE KEY REMOVED. AN INOPERATIVE INTERLOCK MAY ALSO ALLOW THE KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE PARK POSITION.
EITHER CIRCUMSTANCE MAY RESULT IN THE VEHICLE ROLLING AWAY WITHOUT WARNING.
DEALERS WILL INSTALL A NEW LOAD-LIMITING PUSH ROD INTO THE FLOOR SHIFTER LEVER OF THE AFFECTED VEHICLES. OWNER NOTIFICATION BEGAN ON JUNE 14, 2004. OWNERS SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
04V021000 · 2,315,768 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 1998-1999 CHRYSLER SEBRING JXI LIMITED CONVERTIBLES. THE STEERING COLUMN INTERMEDIATE SHAFT COUPLER PINCH BOLT RETAINING PIN COULD SNAG AND/OR FRAY THE EDGE OF THE DRIVER'S SIDE FLOOR MAT.
THIS COULD INTERFERE WITH THE STEERING CONTROL OF THE VEHICLE.
DEALER WILL REPLACE THE STEERING COLUMN INTERMEDIATE SHAFT COUPLER PINCH BOLT AND RETAINING PIN. IN ADDITION, THE FRONT FLOOR MATS WILL BE REPLACED.
01I012000 · 9,800 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: PASSENGER VEHICLES. IF THE RUBBER BOOTS ON THE LOWER LATERAL ARM BALL JOINTS OF THE FRONT SUSPENSION WERE DAMAGED DURING ASSEMBLY, DIRT AND WATER CAN INTRUDE. ALSO, MMC HAS ADDED THE POTENTIAL OF LEAKING MOISTURE, WHICH CAN CAUSE THE BALL STUD TO CORRODE.
THIS CONDITION COULD CAUSE THE LOWER LATERAL ARM BALL JOINT TO SEPARATE, INCREASING THE RISK OF A VEHICLE CRASH. THIS CAMPAIGN SUPERCEDES MMC'S PREVIOUS SAFETY RECALL CAMPAIGN, SEE 99V-066.
DEALERS WILL INSPECT THE LOWER LATERAL ARM BALL JOINT FOR WEAR. BALL JOINTS THAT EXHIBIT WEAR BEYOND THE ESTABLISHED TOLERANCE WILL BE REPLACED WITH NEWLY DESIGNED LATERAL ARM BALL JOINTS. BALL JOINTS THAT ARE WITHIN THE ESTABLISHED TOLERANCE WILL BE CLEANED AND A SPECIAL SEALANT WILL BE APPLIED TO PREVENT INTRUSION OF MOISTURE.
00V421002 · 393,796 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: PASSENGER VEHICLES. IF THE CONVERTIBLE TOP COVER IS NOT INSTALLED CORRECTLY, IT CAN SEPARATE UNEXPECTEDLY FROM THE VEHICLE WHILE DRIVING.
IF THE COVER SEPARATES WHILE DRIVING, IT COULD DISTRACT THE DRIVER INCREASING THE RISK OF A CRASH.
OWNERS WILL RECEIVE AN IMPROVED CONVERTIBLE TOP COVER INSTRUCTION LABEL AND INSTALLATION INSTRUCTIONS.
99I004000 · 175,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE ADJUSTMENT OF THE CABLE CONNECTING THE CONSOLE SHIFTER MECHANISM TO THE IGNITION KEY CAN CAUSE A TRAPPED KEY CONDITION WHICH CAN RESULT IN A LOW FORCE REQUIRED TO DEPRESS THE SHIFT BUTTON. A COMBINATION OF APPLYING A MIS-ADJUSTED RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION, CAN BREAK THE CONNECTING PIN IN THE SHIFTER.
IF THIS HAPPENS, THE "IGNITION-PARK" INTERLOCK SYSTEM WILL BE NONFUNCTIONAL.
DEALERS WILL INSPECT FOR PROPER OPERATION OF THE SYSTEM. ANY VEHICLES THAT ARE NOT FUNCTIONAL AFTER THE INSPECTION WILL HAVE THE SHIFT MECHANISM AND CABLE REPLACED WITH A "SELF-ADJUSTING" DESIGN.
98V183000 · 685,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE DASH PANEL PAD CAN SHIFT INTERFERRING WITH THE THROTTLE CABLE CONTROL.
THE THROTTLE CABLE CONTROL WOULD NOT RETURN TO IDLE INCREASING THE RISK OF A VEHICLE CRASH.
DEALERS WILL REMOVE A PORTION OF THE DASH PANEL PAD SO IT CANNOT INTERFERE WITH THE THROTTLE CABLE CONTROL.
98V045002 · 27,527 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer
1998 Chrysler Sebring recall questions
Transport Canada lists 5 recalls for the 1998 Chrysler Sebring model year. That counts campaigns naming this model year, not recalls on your vehicle: many cover only a VIN range or production window, and some only vehicles found on inspection. NHTSA lists 13 United States campaigns for the US-market model, shown separately; a US campaign may have no Canadian equivalent.
Enter your VIN in Chrysler's Canadian recall lookup, or call a Chrysler dealer with your VIN. In Canada the manufacturer is responsible for showing recall and repair status for each VIN, so its lookup is the authoritative answer. Cardog uses your VIN only to find the model year; the recalls shown here are listed for that model year and are not matched to your VIN.
Not necessarily. NHTSA campaigns cover vehicles sold in the United States, and NHTSA's VIN lookup has no Canadian data. When a defect also affects Canadian vehicles, the manufacturer files a separate notice with Transport Canada, often under a different number and sometimes covering a different set of vehicles. For a Canadian vehicle, go by the Transport Canada listing and Chrysler's Canadian lookup.
Safety recall repairs are normally done at no charge by an authorized Chrysler dealer. The manufacturer's notice for each campaign sets out the remedy and any conditions, so confirm with the dealer when you book.
Once Chrysler's lookup or a dealer confirms a recall applies, book the repair with an authorized Chrysler dealer and bring your VIN. If the manufacturer's notice says not to drive the vehicle or to park it outside, follow that instruction. Parts can take time, so book early.
Follow the manufacturer's notice for that recall. Most allow normal driving until the repair; some tell owners to stop driving or to park outside until it is fixed. Cardog does not grade recalls by severity: the manufacturer's notice and your dealer are the source.
Manufacturers must notify owners they have on record. If you bought the vehicle used or have moved, update your details with Chrysler Canada so notices reach you, and check the manufacturer's lookup from time to time.
Related recall checks
Compare recall listings with alternatives to the 1998 Chrysler Sebring.