Campaigns on record across the Dodge D100 (1964–1990), from Transport Canada and, tagged NHTSA, the United States. Pick a model year for the Canadian listing, and check your VIN with Dodge to confirm which apply.
Note: vehicles equipped with e.f.i. And short (6 1/2 ft.) Box. These vehicles do not comply with CMVSS 301 - fuel system integrity. Vehicles built without a rear bumper may not comply with the rear impact test requirements of the standard. A rear impact resulted in fuel leakage due to pickup box crossmember contact with the fuel pump module nipples. Correction: Vehicles will have reinforcement blocker brackets installed to the undercarriage to restrict pickup box travel.
1990115 · 185 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1990 dodge d100 recalls
IN A REAR END COLLISION, THE PICKUP BOX CROSSMEMBER COULD CONTACT THE FUEL PUMP MODULES FUEL LINE, CAUSING A FUEL LEAK WHICH WOULD BE IN NON-COMPLIANCE WITH FMVSS 301.
CONSEQUENCE OF DEFECT: LEAKAGE OF FUEL COULD CAUSE A FIRE IF A SOURCE OF IGNITION IS PRESENT.
INSTALL TWO PICKUP BOX REINFORCEMENT BLOCKER BRACKETS TO THE UNDERCARRIAGE TO ELIMINATE CONTACT WITH FUEL LINE.
90V124000 · 26,600 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1990 dodge d100 recalls
AUTOMATIC TRANSMISSION MAY CONTAIN A PARK SPRAG ROD ASSEMBLY THAT MAY STICK IN THE TOOTH BUTT UNENGAGED POSITION.
THIS CONDITION COULD ALLOW THE VEHICLE TO ROLL WITH THEGEAR SHIFT LEVER IN PARK POSITION.
ALL INVOLVED VEHICLES WILL HAVE THE PARK SPRAG ROD ASSEMBLIES REPLACED.
87V194000 · 3,500 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1988 dodge d100 recalls
PLASTIC HYDRAULIC CLUTCH SYSTEM COMPONENTS ARE SUBJECT TO EXHAUST SYSTEM HEAT DAMAGE DUE TO PROLONGED COLD, HIGH SPEED IDLE OPERATION.
CONSEQUENCE OF DEFECT: HYDRAULIC FLUID LEAKAGE COULD OCCUR CREATING THE POTENTIAL FOR A MINOR FIRE FROM FLUID CONTACTING THE HOT EXHAUST.
INSTALL PROTECTIVE HEAT SHIELDS BETWEEN THE EXHAUST SYSTEM AND AFFECTED CLUTCH SYSTEM COMPONENTS.
87V040000 · 4,500 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1987 dodge d100 recalls
Certain vehicles may have a brake system master cylinder internal piston seal vacuum venting malfunction. Lack of internal vacuum venting may result in the intermittent loss of front wheel braking capability. Instrument panel lighting will provide warning of partial braking system loss.
1984056 · 245 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1984 dodge d100 recalls
On certain vehicles, the inner and outer carburetor throttle return springs may have been installed incorrectly. This condition may result in spring failure preventing the throttle from returning to a closed position when the accelerator pedal is released.
1979054 · 42 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1979 dodge d100 recalls
DUE TO IMPROPER MATERIAL CONSTRUCTION THE HYDRO-BOOST FLUID RETURN HOSE MAY NOT BE CAPABLE OF WITHSTANDING THE TEMPERATURES AND/OR PRESSURES EXPERIENCED WITH THE HYDRO-BOOST SYSTEM. ALSO, THE HYDRO-BOOST FLUID HIGH PRESSURE HOSE ASSEMBLY MAY HAVE BEEN MISLOCATED, ALLOWING THE ASSEMBLY TO CONTACT THE FRAME SIDE RAIL. ABRASION RESULTING FROM CONTINUED CONTACT ALONG WITH IMPROPER MATERIAL CONSTRUCTION MAY CAUSE PRESSURE HOSE FAILURE. EITHER OF THESE CONDITIONS MAY CAUSE HYDRO-BOOST FLUID LEAKAGE, RESULTING IN THE LOSS OF POWER ASSIST FOR THE STEERING AND BRAKING SYSTEMS. COMPLETE LOSS OF STEERING OR BRAKING WILL NOT OCCUR SINCE BOTH SYSTEMS WOULD REVERT TO MANUAL OPERATION.
THE DEALER WILL INSTALL A HYDRO-BOOST FLUID RETURN HOSE CONSTRUCTED FORM THE PROPER MATERIAL, POSITIONING THE HOSE ASSEMBLY TO ENSURE ADEQUATE CLEARANCE BETWEEN IT AND THE FRAME SIDE RAIL.
78V188000 · 1,400 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1978 dodge d100 recalls
On certain vehicles, the "hydroboost" hydraulic system high pressure hose assembly may be improperly routed and can contact the frame side rail resulting in a leak in the hose assembly. This could result in a loss of power assist to the steering and braking systems.
1978042 · 224 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1978 dodge d100 recalls
IMPROPER ROUTING OF THE "HYDROBOOST" HYDRAULIC SYSTEM HIGH PRESSURE HOSE ASSEMBLY COULD ALLOW A TUBULAR SECTION TO CONTACT THE FRAME SIDE RAIL. ABRASION FROM THE CONTACT COULD RESULT, CAUSING A LEAK IN THE HOSE ASSEMBLY.
THE DEALER WILL REROUTE "HYDROBOOST" HIGH PRESSURE HOSE ASSEMBLIES AND ANY DAMAGED HOSES WILL BE REPLACED.
78V141000 · 1,400 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1978 dodge d100 recalls
Certain vehicles may have been built without an Orifice Spark Advance Control (OSAC) valve required to meet the exhaust pollutant levels specified by CMVSS 1103 - exhaust emissions.
1978002 · 887 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1976 dodge d100 recalls
1–10 of 25