Mercury · 1995–2000
Mystique Recalls
21 known recalls affecting the Mercury Mystique (1995–2000). Enter your VIN to check if your specific vehicle is affected, or browse by model year below.
Mercury Mystique Recalls
Summary
Certain passenger vehicles sold in New Brunswick, Newfoundland, Nova Scotia, Ontario, Prince Edward Island and Quebec . The front coil springs may fracture as a result of corrosion in high corrosion environments. Depending on the location of the fracture, a broken spring could move past the spring seat and contact a front tire in some cases. Some tires have deflated due to contact with a broken spring. Correction : Dealers will install spring catcher brackets.
Summary
Certain passenger vehicles. The rough surface of the heater blower resistor's stainless steel blades can damage the copper surface of the wiring harness connector. The damage could, over time, cause increased resistance in the connector and, due to subsequent terminal relaxation, result in an open circuit condition. The heater blower resistor may overheat causing the attached electrical connector to melt, creating the potential for a fire. Correction: Dealers will install a new heater blower resistor and a new wire jumper harness.
Summary
On certain vehicles equipped with 2.5 litre V6 engines, tightening of the engine cooling fan motor bearings, up to and including motor stall, can result in increased motor torque and higher than normal motor current and accompanying high motor temperatures. Overheating of the cooling fan motor due to excessive current can result in smoke and odors from bearing grease, insulation and other internal motor components. If electrical current continues to be applied to the motor, internal motor components could ignite possibly igniting other engine compartment components. Correction: Dealers will install a Positive Temperature Coefficient device (a solid state resettable fuse-like device) in-line with each fan motor.
Summary
On certain vehicles, the pressure conscious reducing valve (PCRV) in each of the rear brakes may be subject to malfunction due to corrosion when operated in areas of high road salt use. If both PCRVs malfunction, vehicle handling may be adversely affected during braking as a result of the rear wheels locking, which could potentially result in a vehicle crash. Correction: Dealers will install improved PCRVs in the rear brake system.
Summary
On certain vehicles, the fuel filler pipe vent hose may have less than the intended level of ozone resistance, which could result in the hose becoming brittle and cracking. A cracked hose could result in fuel leakage when the vehicle is being fueled. Fuel leakage in sufficient quantity in the presence of an ignition source could potentially result in a fire. Correction: Dealers will install a fuel filler vent hose containing the appropriate blend of PVC and nitrile rubber.
Summary
On certain vehicles, the air bag sensor wiring pigtail insulation may become brittle and crack over time due to water accumulation in the protective convolute combined with high under hood temperatures and routing of the pigtail near the radiator. This could result in the air bag warning light illuminating and disabling of the air bag. Correction: Air bag sensors with revised wiring insulation will be installed. Also, vehicles which have the air bag warning light illuminated will have a new air bag diagnostic monitor installed if required.
Summary
On certain vehicles, the accelerator cable may have been manufactured with a burr on or near the end of the cable sleeve interior. This burr could fray the core wire which in turn could cause the accelerator not to return to idle when the accelerator pedal is released. This could result in a vehicle crash. Correction: Accelerator cable will be replaced with a revised version which has a flared conduit sleeve end and molded-on end fitting.
Summary
On certain vehicles, the terminals at the headlight switch and wiring harness connector may experience heat damage as a result of overheating. This can cause distortion of the terminal and an open circuit in the instrument panel illumination, parking lamp and tail lamp circuits. Correction: Dealers will install a headlamp switch wiring connector containing bronze terminals and inspect and if necessary, replace the headlamp switch.
Summary
Certain vehicles do not comply with the requirements of CMVSS 114 - Locking System. It may be possible to rotate the ignition key to the "LOCK" position and remove the key without the shift lever and transmission being in "PARK". Correction: Vehicles will be inspected and if the ignition key can be removed in gear positions other than "PARK", the steering column will be replaced.
Summary
Certain vehicles do not comply with CMVSS 205 - glazing materials. The windshields on were produced without the "AS1" mark as required by American National Standards Institute (ANSI) Z26.1. These windshields fully meet all of the requirements of Standard 205. Correction: Since the absence of the AS1 mark is highly unlikely to produce any risk of injury, no corrective action will be taken.
Showing 1-10 of 21 recalls
Related Recall Checks
Check recalls for specific Mercury Mystique model years