1998 Ford Contour
Safety Recalls & Notices
We found 21 safety recalls for the 1998 Ford Contour. Recalls are sourced from both NHTSA (US) and Transport Canada databases. Contact your authorized Ford dealer to schedule free repairs.
Summary
Certain passenger vehicles sold in New Brunswick, Newfoundland, Nova Scotia, Ontario, Prince Edward Island and Quebec . The front coil springs may fracture as a result of corrosion in high corrosion environments. Depending on the location of the fracture, a broken spring could move past the spring seat and contact a front tire in some cases. Some tires have deflated due to contact with a broken spring. Correction : Dealers will install spring catcher brackets.
Summary
Certain passenger vehicles. The rough surface of the heater blower resistor's stainless steel blades can damage the copper surface of the wiring harness connector. The damage could, over time, cause increased resistance in the connector and, due to subsequent terminal relaxation, result in an open circuit condition. The heater blower resistor may overheat causing the attached electrical connector to melt, creating the potential for a fire. Correction: Dealers will install a new heater blower resistor and a new wire jumper harness.
Summary
On certain vehicles, the pressure conscious reducing valve (PCRV) in each of the rear brakes may be subject to malfunction due to corrosion when operated in areas of high road salt use. If both PCRVs malfunction, vehicle handling may be adversely affected during braking as a result of the rear wheels locking, which could potentially result in a vehicle crash. Correction: Dealers will install improved PCRVs in the rear brake system.
Summary
On certain vehicles, the air bag sensor wiring pigtail insulation may become brittle and crack over time due to water accumulation in the protective convolute combined with high under hood temperatures and routing of the pigtail near the radiator. This could result in the air bag warning light illuminating and disabling of the air bag. Correction: Air bag sensors with revised wiring insulation will be installed. Also, vehicles which have the air bag warning light illuminated will have a new air bag diagnostic monitor installed if required.
Summary
On certain vehicles, the accelerator cable may have been manufactured with a burr on or near the end of the cable sleeve interior. This burr could fray the core wire which in turn could cause the accelerator not to return to idle when the accelerator pedal is released. This could result in a vehicle crash. Correction: Accelerator cable will be replaced with a revised version which has a flared conduit sleeve end and molded-on end fitting.
Summary
On certain vehicles, the terminals at the headlight switch and wiring harness connector may experience heat damage as a result of overheating. This can cause distortion of the terminal and an open circuit in the instrument panel illumination, parking lamp and tail lamp circuits. Correction: Dealers will install a headlamp switch wiring connector containing bronze terminals and inspect and if necessary, replace the headlamp switch.
Summary
Certain vehicles do not comply with CMVSS 205 - glazing materials. The windshields on were produced without the "AS1" mark as required by American National Standards Institute (ANSI) Z26.1. These windshields fully meet all of the requirements of Standard 205. Correction: Since the absence of the AS1 mark is highly unlikely to produce any risk of injury, no corrective action will be taken.
Summary
On certain vehicles, the floor shift automatic transmission control may be damaged if subjected to certain vehicle interior cleaning products. If exposed to these products, the transmission gear position indicator may deteriorate and not correctly indicate the actual gear position. If this occurs, the shifter will continue to operate normally, but there is the potential for incorrect gear selection. Correction: Automatic transmission floor shift control will be replaced.
Summary
THESE VEHICLES DO NOT COMPLY WITH C.M.V.S.S. 108 - LIGHTING SYSTEM AND RETROREFLECTIVE DEVICES. THE HEADLIGHT AIMING INSTRUCTIONS PROVIDED IN THE OWNER GUIDES ARE NOT SUFFICIENTLY CLEAR. CORRECTION: REVISED OWNER GUIDES WILL BE MAILED TO OWNERS.
Summary
FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.
Potential Consequence
THE NUTS INCLUDED IN THE PACKAGING FOR THESE BALL JOINT ASSEMBLIES ARE MISSING THE INTENDED PREVAILING TORQUE (SELF-LOCKING) FEATURE. IF THE INCORRECT NUT WAS TO BECOME LOOSE, THE JOINING MEMBERS MAY LOOSEN LEADING TO A SEPARATION OF THE BALL JOINT. THIS MAY RESULT IN LOSS OF VEHICLE CONTROL, POSSIBLY RESULTING IN A VEHICLE CRASH.
Remedy
FEDERAL MOGUL WILL NOTIFY OWNERS AND REPLACE THE PARTS FREE OF CHARGE. THE RECALL BEGAN ON MAY 22, 2008. OWNERS CAN CONTACT FEDERAL MOGUL AT 877-489-6659.
21 Active Recalls
Requires attention
Ford Contour by Year
1998 Ford Contour Recall FAQs
Common questions about recalls for this vehicle
Related Recall Checks
Compare recall history with competitors and alternatives to the 1998 Ford Contour.