Campaigns on record across the Cadillac Limousine (1978–2001), from Transport Canada and, tagged NHTSA, the United States. Pick a model year for the Canadian listing, and check your VIN with Cadillac to confirm which apply.
VEHICLE DESCRIPTION: CERTAIN LIMOUSINE, ARMORED AND HEARSE MODEL VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES HAVE AN INCORRECT TIRE PRESSURE LABEL.
INCORRECT TIRE INFLATION PRESSURE CAN DAMAGE TIRES, AFFECT VEHICLE HANDLING, AND INCREASE THE RISK OF A CRASH.
OWNERS WILL BE PROVIDED WITH CORRECT LABELS.
00V431000 · 2,807 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 2001 cadillac limousine recalls
VEHICLE DESCRIPTION: LIMOUSINE AND HEARSE MODEL VEHICLES. THE RIGHT FRONT BRAKE HOSE CAN CONTACT THE WHEEL RESULTING IN DAMAGE TO THE BRAKE HOSE.
IF THE HOSE BECOMES DAMAGED, THERE CAN BE A LOSS OF BRAKE FLUID AND PRESSURE IN HALF OF THE BRAKE SYSTEM. THE BRAKE PEDAL WILL BE LOWER THAN NORMAL AND STOPPING DISTANCES WILL BE LONGER, INCREASING THE RISK OF A CRASH.
DEALERS WILL REPLACE THE RIGHT FRONT BRAKE HOSE ASSEMBLY. THE LEFT FRONT BRAKE HOSE ASSEMBLY WILL ALSO BE REPLACED TO PREVENT THE POSSIBILITY OF INCORRECT POSITION OF THE HOSE DURING ANY FUTURE SERVICE.
00V056000 · 1,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 2000 cadillac limousine recalls
REAR WHEEL BRAKE CYLINDERS ARE TOO SMALL TO ALLOW FOR PROPER BRAKING.
STOPPING DISTANCE REQUIREMENTS OF FMVSS 105 ARE NOT METWITH POWER BRAKING ASSIST UNIT INOPERATIVE.
REPLACE ORIGINAL 1" REAR WHEEL BRAKE CYLINDER WITH A 1 1/16" CYLINDER.
91V097000 · 73 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1991 cadillac limousine recalls
REAR WHEEL BRAKE CYLINDERS ARE TOO SMALL TO ALLOW FOR PROPER BRAKING.
STOPPING DISTANCE REQUIREMENTS OF FMVSS 105 ARE NOT METWITH POWER ASSIST BRAKING UNIT INOPERATIVE.
REPLACE ORIGINAL 1" REAR WHEEL BRAKE CYLINDER WITH A 1 1/16" CYLINDER.
91V095000 · 14 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1990 cadillac limousine recalls
THE NUTS WHICH FASTEN THE LOWER ARM BALLJOINT TO THE STEERING KNUCKLE MAY NOT HAVE BEEN SECURELY TIGHTENED.
DEALER WILL TIGHTEN ANY LOOSE STEERING KNUCKLE ATTACHING NUTS. IF NECESSARY, LOWER CONTROL ARM BALLJOINTS AND STEERING KNUCKLES WILL BE REPLACED.
83V066000 · 3,959 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1983 cadillac limousine recalls
THE HEADS MAY BREAK OFF THE FRONT OUTBOARD SEAT BELT ANCHOR BOLTS DURING NORMAL VEHICLE OPERATION EVEN UNDER NO LOAD CONDITIONS. THIS IS DUE TO THE COMBINATION OF BOLTS USED, HIGH INSTALLATION TORQUE AND ARRANGEMENT OF THE BODY ANCHORAGE.
DEALER WILL REPLACE ALL ORIGINAL EQUIPMENT FRONT OUTBOARD SEAT BELT ANCHOR BOLTS ON THE AFFECTED VEHICLES AT NO COST TO OWNER.
79V247000 · 1,326,404 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1979 cadillac limousine recalls
THE REAR WHEEL MOUNTING BOLTS ON THE AFFECTED VEHICLES, ARE BRITTLE AND THEREFORE MAY FRACTURE. THIS BRITTLENESS IS DUE TO IMPROPER HEAT TREATMENT DURING MANUFACTURE. IF THE BOLTS BREAK, THE TIRE AND WHEEL ASSEMBLY MAY SEPARATE FROM THE VEHICLE.
DEALER WILL INSPECT AND, IF NECESSARY, WILL REPLACE DEFECTIVE BOLTS ON ALL AXLES AND THE TEN REAR AXLE WHEEL MOUNTING BOLTS, FREE OF CHARGE.
77V200000 · 4,504 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1978 cadillac limousine recalls
Cadillac Limousine by year
Related recall checks
Check recalls for specific Cadillac Limousine model years