Campaigns on record across the BMW 735 (1985–1993), from Transport Canada and, tagged NHTSA, the United States. Pick a model year for the Canadian listing, and check your VIN with BMW to confirm which apply.
FEED FUEL HOSES CAN HARDEN AND "SET" OVER TIME, ALLOWING A SEEPAGE OF FUEL AT THE CONNECTION BETWEEN THE HOSE AND THE ENGINE FITTING. THE CLAMP USED TO HOLD THE HOSE TO THE FITTING IS UNABLE TO COMPENSATE FOR THE HARDENING OF THE FEED FUEL HOSE.
FUEL SEEPAGE BETWEEN THE FEED FUEL HOSE AND THE ENGINE FITTING CAN RESULT IN FREE FUEL IN THE ENGINE COMPARTMENT, WHICH COULD RESULT IN A FIRE WHEN EXPOSED TO A SOURCE OF IGNITION.
A REDESIGNED FEED FUEL HOSE AND HOSE CLAMP WILL BE INSTALLED TO ALLEVIATE THE FUEL SEEPAGE.
94V066000 · 116,300 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1993 bmw 735 recalls
SOME OF THESE VEHICLES ARE EQUIPPED WITH A THROTTLE HOUSING ON WHICH THE THROTTLE VALVE SHAFT RETAINING NUT WAS NOT SUFFICIENTLY TIGHTENED.
IF THE NUT WERE TO LOOSEN, MOVEMENT OF THE THROTTLE VALVECOULD BE IMPAIRED, RESULTING IN THE VEHICLE BEING UNABLE TO DECELERATE WHEN THEGAS PEDAL IS RELEASED.
THOSE THROTTLE HOUSINGS WITH SUSPECT MANUFACTURING CODES WILL HAVE THE THROTTLE VALVE SHIFT RETAINING NUT TORQUE TESTED, AND THOSE WITH INSUFFICIENT NUT TORQUE WILL BE REPLACED.
92V101000 · 637 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1991 bmw 735 recalls
UNDER CERTAIN CONDITIONS, FRONT SEAT CENTER, FOLD-DOWN ARM REST MAY CONTACT THE SAFETY BELT BUCKLE, CAUSING DAMAGE TO THE RELEASE BUTTON AND PREVENTING THE BELT TONGUE FROM LATCHING WHEN BUCKLING UP.
OCCUPANT WOULD NOT BE PROPERLY RESTRAINED AND COULD BE INJURED IN THE EVENT OF A SUDDEN STOP OR ACCIDENT.
REPLACE FRONT SEAT SAFETY BELT BUCKLES WITH SHORTER VERSION THAT WILL NOT CONTACT THE ARMRESTS. NOTE: OWNER NOTIFICATION DATE; 2/90 IS PREPARED IN DRAFT FORM.
90V016000 · 62,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1990 bmw 735 recalls
THE DRIVER AND/OR PASSENGER SEATBACKS MAY NOT HAVE BEEN FULLY ATTACHED TO THE SEAT BASE RECLINING ARMS (ATTACHING BRACKETS).
THERE MAY BE LOOSENESS OF, OR NOISE IN, THE SEATBACK;ALSO, DURING A SEVERE REAR IMPACT, SEATBACK MIGHT NOT SUPPORT THE OCCUPANT.
MANUALLY SEAT THE SEATBACK ON THE BASE.
88V135000 · 8,187 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1988 bmw 735 recalls
BRAKE LIGHT SWITCH COULD OVERHEAT, EVENTUALLY LEADING TO MELTING OF PLASTIC INTERNAL PARTS IN AREA OF ELECTRICAL CONTACTS.
CONSEQUENCE OF DEFECT: SWITCH PLUNGER COULD JAM, RENDERING BRAKE LIGHTS EITHER INOPERATIVE OR CONTINUOUSLY ILLIMINATED, REGARDLESS OF BRAKE PEDAL OPERATION.
REPLACE BRAKE LIGHT SWITCH WITH REVISED SWITCH WITH INCREASED ELECTRICAL LOAD CAPACITY.
86V151000 · 97,300 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1987 bmw 735 recalls
INCORRECT MACHINING OF THE SEATING SURFACE OF THE WHEELS WHERE IT CONTACTS THE HUB OF THE CAR MAY PREVENT THE WHEELS FROM MOUNTING SECURELY TO THE HUB. THIS MAY CAUSE THE WHEEL TO BREAK AND COULD FALL OFF. CONSEQUENCE OF DEFECT: THE WHEELS COULD LOOSEN AND A CRASH COULD OCCUR. OWNERS SHOULD NOT DRIVE THEIR CARS UNTIL REPAIR WORK HAS BEEN DONE.
SCRAPE THE CENTER BORE OF THE RIM SO IT CAN CLEAR THE CENTER OF THE HUB.
85V065000 · 40 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1985 bmw 735 recalls