Campaigns on record across the Nissan 240sx (1989–1995), from Transport Canada and, tagged NHTSA, the United States. Pick a model year for the Canadian listing, and check your VIN with Nissan to confirm which apply.
THE (Takata) ABS PLASTIC FRONT SEAT BELT RELEASE BUTTONS ON THESE VEHICLES MAY BREAK ALLOWING PLASTIC PIECES TO FALL INTO THE BUCKLE ASSEMBLY. IF THIS SHOULD HAPPEN, A NO LATCH, FALSE LATCH OR FAILURE TO UNLATCH CONDITION COULD OCCUR CREATING THE RISK OF PERSONAL INJURY IN THE EVENT OF A CRASH OR SUDDEN STOP. CORRECTION: FRONT SEAT BELT BUCKLES WILL BE REPAIRED OR REPLACED AS NECESSARY.
1995084 · 106,721 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1991 nissan 240sx recalls
THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY.
THE SAFETY BELTS WOULD NOT PROVIDE ADEQUATE PROTECTION TO AN OCCUPANT IN A VEHICLE CRASH.
OWNERS SHOULD PROMPTLY CHECK THE CONDITION AND OPERATION OF BOTH FRONT SAFETY BELT BUCKLES AND CAREFULLY INSPECT THE RED RELEASE BUTTON FOR ANY BREAKS OR CRACKS. THEY SHOULD ENSURE THAT BOTH BUCKLES ARE OPERATING PROPERLY BY INSERTING EACH LATCH PLATE INTO ITS BUCKLE, TUGGING ON THE BELT TO MAKE SURE THE LATCH IS SECURELY LOCKED, AND THEN PRESSING THE RELEASE BUTTON. THE LATCH PLATE SHOULD POP OUT OF THE BUCKLE WHEN THE BUTTON IS PRESSED. IF EITHER RELEASE BUTTON SHOWS A SIGN OF BREAKING OR CRACKING OR IF EITHER BUCKLE FAILS TO OPERATE PROPERLY, OWNERS SHOULD PROMPTLY CONTACT THEIR AUTHORIZED DEALER TO SCHEDULE AN APPOINTMENT TO HAVE THE BUCKLE REPLACED OR REPAIRED FREE OF CHARGE.
95V103002 · 2,730,462 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1991 nissan 240sx recalls
THE BRAKE WARNING LAMP WILL NOT ILLUMINATE IF THE BRAKE FLUID LEVEL IN THE MASTER CYLINDER RESERVOIR DROPS SUFFICIENTLY TO ACTIVATE THE LOW LEVEL SWITCH AS SPECIFIED IN C.M.V.S.S. 105 - HYDRAULIC BRAKE SYSTEMS. CORRECTION: A SPECIAL SUB HARNESS WILL BE INSTALLED WHICH WILL CAUSE THE WARNING LAMP TO ILLUMINATE WHEN THE LOW LEVEL SWITCH IS ACTIVATED.
1994126 · 773 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1995 nissan 240sx recalls
THE INSTRUMENT PANEL BRAKE WARNING LIGHT WILL NOT ILLUMINATE WHEN THE BRAKE FLUID LEVEL IN THE MASTER CYLINDER DROPS SUFFICIENTLY TO ACTIVATE THE LOW LEVEL SWITCH DUE TO AN IMPROPERLY WIRED DIODE, REQUIRED BY FMVSS NO. 105, "HYDRAULIC BRAKE SYSTEMS."
CONSEQUENCE OF NON-COMPLIANCE: THERE WOULD BE NO INDICATION TO THE DRIVER OF THE VEHICLE THAT BRAKE FLUID WAS LOW. LOW BRAKE FLUID CAN BE CAUSED BY A LEAK IN THE SYSTEM WHICH MAY RESULT IN PARTIAL OR COMPLETE LOSS OF BRAKES AND AN ACCIDENT.
DEALERS WILL CORRECT THE ELECTRICAL CIRCUIT FOR THE BRAKE WARNING SYSTEM SO THAT THE WARNING LAMP WILL ILLUMINATE WHEN THE LOW LEVEL SWITCH IS ACTIVATED.
94V135000 · 7,500 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorized dealer · All 1995 nissan 240sx recalls
Nissan 240sx by year
Related recall checks
Check recalls for specific Nissan 240sx model years