Campaigns on record across the Cadillac XLR (2003–2009), from Transport Canada and, tagged NHTSA, the United States. Pick a model year for the Canadian listing, and check your VIN with Cadillac to confirm which apply.
TI AUTOMOTIVE IS RECALLING CERTAIN FUEL PUMPS, PART NUMBERS TU456 AND TU303, SOLD UNDER VARIOUS BRAND NAMES AS AFTERMARKET AND REPLACEMENT EQUIPMENT FOR THE MOTOR VEHICLES LISTED ABOVE. THE DEFECTIVE FUEL PUMP MAY SEIZE, STOPPING THE FUEL FLOW TO THE ENGINE CREATING A STALLING CONDITION.
A VEHICLE CRASH COULD OCCUR SHOULD THE ENGINE STALL WHILE IN USE.
TI AUTOMOTIVE WILL NOTIFY OWNERS OF RECORD AND WILL REPLACE ANY DEFECTIVE FUEL PUMP WITH A NEW OR REWORKED FUEL PUMP FREE OF CHARGE. THE SAFETY RECALL BEGAN ON FEBRUARY 22, 2011. OWNERS MAY CONTACT TI AUTOMOTIVE AT 1-866-867-3759 OR LOG ON TO WWW.RECALLRESPONSE.COM.
11E009000 · 4,887 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 2009 cadillac xlr recalls
ON CERTAIN PASSENGER VEHICLES, THE DAYLIGHT RUNNING LIGHTS (DRL), TURN SIGNAL, AND PARKING LAMPS USE THE SAME BULB. THE BULB MAY BECOME DAMAGED FROM VIBRATION WITHIN A LOOSE FITTING SOCKET OR AIR ENTERING THE BULB DUE TO AN INADEQUATE SEAL. BOTH OF THESE CONDITIONS WILL CAUSE THE BULB TO BURN OUT PREMATURELY.
IF THIS WERE TO OCCUR, THE DRIVER WOULD NOTICE THAT THE ARROW IN THE INSTRUMENT PANEL WOULD FLASH FASTER THAN NORMAL WHEN THE TURN SIGNAL IS ACTIVATED. THE LOSS OF THE DRL AND TURN SIGNALS COULD FAIL TO WARN OTHERS OF THE DRIVER'S PRESENCE OR INTENTIONS AND COULD LEAD TO A VEHICLE CRASH.
DEALERS WILL REPLACE THE SOCKET AND BULB IN BOTH LAMPS FREE OF CHARGE. THE RECALL BEGAN ON JULY 31, 2006. OWNERS MAY CONTACT CADILLAC AT 1-866-982-2339.
06V263000 · 7,689 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 2005 cadillac xlr recalls
On certain vehicles the bulb used for the Daytime Running Lights (DRL), turn signals, and parking lamps may burn out prematurely. Correction: Dealers will replace the socket and bulb in both lamps.
2006172 · 316 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 2005 cadillac xlr recalls
Certain vehicles do not comply with the requirements of CMVSS 124 - Accelerator Control Systems. The Electronic Throttle Control (ETC) accelerator pedal assembly may not return the engine to idle in three seconds or less at low ambient temperatures if either of the two throttle return springs is broken. Correction: Dealers will replace the ETC pedal assembly.
2005034 · 1,611 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 2004 cadillac xlr recalls
CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 124, 'ACCELERATOR CONTROL SYSTEMS.' IF ONE OF THE TWO ACCELERATOR PEDAL RETURN SPRINGS FAILS AND THE TEMPERATURE IS -22 DEGREES F TO -40 DEGREES F, THE ENGINE MAY NOT RETURN TO IDLE WITHIN THREE SECONDS, AS REQUIRED.
IF THIS WERE TO OCCUR, GREATER BRAKE PEDAL FORCE AND A LONGER DISTANCE MAY BE REQUIRED TO STOP THE VEHICLE.
DEALERS WILL REPLACE THE ACCELERATOR PEDAL ASSEMBLY. THIS RECALL BEGAN ON MARCH 8, 2005. OWNERS MAY CONTACT CADILLAC AT 1-866-982-2339 OR PONTIAC AT 1-800-620-7668.
05V046000 · 19,924 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 2004 cadillac xlr recalls
CERTAIN PASSENGER VEHICLES WERE PRODUCED WITH ONE OR BOTH REAR BRAKE HYDRAULIC LINES THAT CAN COME IN CONTACT WITH OR BE AFFECTED BY HEAT FROM THE LEFT ENGINE EXHAUST MANIFOLD AND THE LEFT EXHAUST PIPE. THE BRAKE FLUID COULD REACH ELEVATED TEMPERATURES AND BOIL.
IF THE BRAKE FLUID BOILS IN A REAR BRAKE LINE, THE EFFECTIVENESS OF THE REAR BRAKE SYSTEM WOULD BE REDUCED WHICH COULD RESULT IN A BRAKE LINE LEAK AND LOSS OF BRAKE FLUID. IF ENOUGH FLUID LEAKS FROM THE REAR BRAKE SYSTEM SO THAT BRAKE PEDAL APPLICATION CAN NO LONGER BUILD PRESSURE TO THE REAR BRAKES. THE OPERATOR OF THE VEHICLE WILL EXPERIENCE LIMITED BRAKING WHICH COULD RESULT IN A CRASH.
DEALERS WILL (1) INSPECT THE LEFT ENGINE EXHAUST MANIFOLD CLIP FOR PROPER ALIGNMENT AND PLACEMENT ON THE BODY-MOUNTED STUD. IF INCORRECT, THEY WILL REPOSITION THE CLIP ON THE BRAKE LINES AND REINSTALL THE CLIP ON THE STUD; (2) THE DEALER WILL VERIFY THAT BOTH REAR BRAKE LINES HAVE THE PROPER CLEARANCE TO THE LEFT EXHAUST PIPE. THEY WILL REPOSITION THE LINES BY BENDING AS NECESSARY; (3) DEALERS WILL REMOVE THE MACHINING TAB FROM THE REAR DIFFERENTIAL HOUSING. ALSO, DEALERS ARE TO INSPECT THE BRAKE LINES FOR WEAR IN THESE RELATED AREAS AND REPAIR OR REPLACE IF THERE IS ANY SIGN OF WEAR-THROUGH ON THE NYLON OVERCOATING. THE RECALL BEGAN ON JANUARY 18, 2005. OWNERS SHOULD CONTACT CADILLAC AT 1-866-982-2239 OR CHEVROLET AT 1-800-630-2438.
04V525000 · 5,225 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 2005 cadillac xlr recalls
Certain vehicles were produced with one or both rear brake hydraulic lines that can come in contact with or be affected by heat from the left engine exhaust manifold and the left exhaust pipe. Also, on some 2005 vehicles, the crossover brake line to the right rear brake can come in contact with the rear differential case. In both cases, a half system brake failure could occur, resulting in increased stopping distances. Correction: Dealers will repair/reposition the rear brake lines.
2004389 · 290 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 2005 cadillac xlr recalls
ON CERTAIN PASSENGER VEHICLES INVOLVED IN THIS CAMPAIGN, THE LOWER CONTROL ARM BALL STUD NUT/WASHER ASSEMBLIES WITH WASHERS WERE MADE OF THE WRONG MATERIAL. THE WASHERS MAY FRACTURE AND BECOME LOOSE OR FALL AWAY FROM THE VEHICLE, REDUCING CLAMP LOAD. SEPARATION OF THE CONTROL ARM BALL STUD AND STEERING KNUCKLE, DUE TO DISENGAGEMENT OF THE TAPERED ATTACHMENT AND RETAINING NUT, IS POSSIBLE.
IF THE CONTROL ARM SEPARATES FROM THE KNUCKLE, THE AFFECTED CORNER OF THE VEHICLE WILL DROP AND THE CONTROL ARM WOULD BE FORCED DOWNWARD, CONTACTING THE WHEEL. THE AFFECTED WHEEL COULD TILT OUTWARD AND CREATE A DRAGGING ACTION THAT WOULD TEND TO SLOW THE VEHICLE AND CREATE A TENDENCY FOR THE VEHICLE TO TURN IN THE DIRECTION OF THE AFFECTED WHEEL. IN EXTREME SITUATIONS, THE AFFECTED WHEEL ASSEMBLY COULD SEPARATE FROM THE VEHICLE. SEPARATION OF THE WHEEL ASSEMBLY WOULD ALSO SEVER THAT WHEEL;S HYDRAULIC BRAKE HOSE AND RESULT IN DIMINISHED BRAKING PERFORMANCE OF THE VEHICLE, WHICH COULD RESULT IN A CRASH.
DEALERS WILL INSPECT THE BALL STUD JOINTS AND MEASURE THE TORQUE OF THE NUT FOR ALL FRONT LOWER CONTROL ARMS IN ALL MODELS AFFECTED AS WELL AS THE REAR LOWER CONTROL ARMS ON THE XLR AND CORVETTE. IF THE TORQUE IS NOT AT SPECIFICATION, THE DEALERS WILL REPLACE THE BALL STUD, THE KNUCKLE, AND THE NUT. IF THE TORQUE IS AT SPECIFICATION, THE DEALERS WILL REPLACE THE NUT/WASHER ASSEMBLY ONLY. THE RECALL WILL BEGIN ON AUGUST 25, 2004. OWNERS SHOULD CONTACT CADILLAC AT 1-866-982-2339 OR CHEVROLET AT 1-800-630-2438.
04V273000 · 41,928 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 2004 cadillac xlr recalls
Certain vehicles were produced with lower control arm ball stud nut/washer assemblies with washers made of the wrong steel material. The washers may fracture and become loose or fall away from the vehicle, reducing clamp load. Separation of the control arm ball stud and steering knuckle, due to disengagement of the tapered attachment and retaining nut, is possible and may occur without prior indication to the vehicle operator. If the control arm separates from the knuckle, the affected corner of the vehicle will drop and the control arm would be forced downward, contacting the wheel. The affected wheel could tilt outward and create a dragging action that would tend to slow the vehicle and create a tendency for the vehicle to turn in the direction of the affected wheel. In extreme situations, the affected wheel assembly could separate from the vehicle. Separation of the wheel assembly would also sever that wheel's hydraulic brake hose and result in diminished braking performance of the vehicle, which could result in a crash. Correction: Dealers will install a new nut and washer, and if required, replace the ball stud and/or steering knuckle.
2004206 · 1,411 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 2004 cadillac xlr recalls
Cadillac XLR by year
Related recall checks
Check recalls for specific Cadillac XLR model years