Campaigns on record across the Dodge Mb300 (1971–1979), from Transport Canada and, tagged NHTSA, the United States. Pick a model year for the Canadian listing, and check your VIN with Dodge to confirm which apply.
Certain vehicles may be equipped with flexible steering couplings that were machined by the supplier with the roll pin hole out of location. This condition results in looseness of the couplings spline engagement which may promote a fretting corrosion failure of the splines. This could cause a loss of steering control.
1980099 · 23,755 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1976 dodge mb300 recalls
DUE TO A COMBINATION OF DISC BRAKE PAD WEAR AND TURN STOP WEAR ON CERTAIN VEHICLES, THERE MAY BE AN INCREASE IN BRAKE PEDAL TRAVEL AND A REDUCTION IN FRONT BRAKING EFFECTIVENESS FOLLOWING A FULL TURN. ALSO, A FRAME CRACK COULD DEVELOP AND COULD EXTEND THROUGH ALL OR MOST OF THE RAIL SECTION.
UPON INSPECTION DEALER WILL REPLACE EITHER THE LEFT OR RIGHT TURN STOP BRACKET TO CORRECT THE FRONT BRAKES. IF FRAME IS CRACKED IT WILL BE WELDED AND A ROD REINFORCEMENT WILL BE INSTALLED OVER THE CRACKED AREA.
80V073000 · 3,50,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1977 dodge mb300 recalls
On certain vehicles, the vehicle certification (statement of compliance) label may contain incorrect dates for the date of chassis manufacture. The labels show january 1980 as the date of chassis manufacture rather than the actual dates of january to may 1979. These vehicles do not comply with Canada Motor Vehicle Safety Regulation 6 - Statement of Compliance.
1980051 · 16 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1979 dodge mb300 recalls
THE FEDERAL MOTOR VEHICLE SAFETY STANDARD CERTIFICATION LABELS ON THE INVOLVED VEHICLES MAY CONTAIN INCORRECT DATA FOR THE INCOMPLETE VEHICLE (CHASSIS) DATE OF MANUFACTURE AND FOR THE DATE OF FEDERAL MOTOR VEHICLE SAFETY STANDARD CONFORMANCE EFFECTIVENESS.
DEALER WILL PROVIDE CERTIFICATION LABELS WITH THE PROPER DATES OF MANUFACTURE AT NO CHARGE TO OWNER. NEW LABELS MAY BE INSTALLED BY OWNERS OR BY DEALERS AT OWNER"S REQUEST.
80V039000 · 3,500 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1979 dodge mb300 recalls
THE FRONT RAIL EXTENSION MAY EXPERIENCE FATIGUE CRACKING NEAR THE AREA WHERE THE POWER STEERING GEAR ATTACHES TO THE FRAME. IF THE CRACK PROGRESSES THROUGH MOST OR ALL OF THE RAIL SECTION, STEERING SYSTEM FREE PLAY ACCOMPANIED BY METALLIC RATTLE NOISE WILL BE EXPERIENCED.
AFFECTED VEHICLES WILL BE WELD REPAIRED AND A REINFORCEMENT ROD WILL BE INSTALLED OVER THE CRACKED AREA.
80V027000 · 10,00,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1978 dodge mb300 recalls
CONDENSATE WATER MAY ACCUMULATE IN THE AIR CONDITIONING BLOWER HOUSING; THERE IS A HIGH PROBABILITY THAT THIS WATER WILL CAUSE THE BLOWER MOTOR TO FAIL. BLOWER MOTOR FAILURE WOULD DISABLE THE AIR CONDTIONING UNIT AND THERE WOULD BE NO WAY TO DEFROST OR DEFOG THE WINDSHIELD.
DEALER WILL DRILL A 1/4 INCH DRAIN HOLE IN THE BOTTOM OF THE AIR CONDITIONING BLOWER HOUSING TO PREVENT WATER ACCUMULATION, WITHOUT CHARGE TO OWNER.
79V176000 · 68,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1979 dodge mb300 recalls
THE FRONT BRAKE HOSE ROUTING MAY ALLOW INTERFERENCE BETWEEN THE HOSES AND THE TIRE AND WHEEL ASSEMBLIES DURING EXTREME TURNING ANGLES.
DEALER WILL REPLACE BOTH LEFT AND RIGHT FRONT BRAKE HOSES AND INSTALL A NEW BRAKE HOSE SUPPORT BRACKET TO ELIMINATE CONTACT WITH TIRE/WHEEL.
79V105000 · 50,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1978 dodge mb300 recalls
LOWER CONTROL ARMS MAY FRACTURE IN THE AREA ADJACENT TO THE LOWER BALL JOINT, RESULTING IN SEPARATION OF THE BALL JOINT FROM THE ARM.
DEALER WILL INCREASE THE STRENGTH OF BOTH LOWER CONTROL ARMS BY INSTALLING WELDED REINFORCEMENTS.
79V104000 · 27,000 units in campaign · NHTSA
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1979 dodge mb300 recalls
On certain vehicles, improper front brake hose routing may allow the brake hoses to rub against the tire and wheel assemblies during extreme turning angles. This may result in brake hose failure and loss of front wheel braking capability. The rear brake system is not affected.
1979076 · 5,545 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1978 dodge mb300 recalls
On certain vehicles, the front suspension lower control arms may fracture adjacent to the lower ball joint resulting in separation of the ball joint from the control arm and loss of steering control.
1979075 · 2,742 units in campaign · Transport Canada
Applies only if the manufacturer confirms your VIN · repair by an authorised dealer · All 1979 dodge mb300 recalls
1–10 of 13
Dodge Mb300 by year
Related recall checks
Check recalls for specific Dodge Mb300 model years